Bedienungsanleitung Ariston STEA-serie (Seite 54 von 68) (Deutsch, Englisch, Holländisch, Französisch)

655848

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Picture 15 – PROfessional TECH: lights

Green indicator light ON – Red indicator light

OFF:



Red indicator light ON:



Contact your

installer.

Green indicator light OFF:

 The boiler

is no longer protected against corrosion.

Contact the installer.

Picture 15a- HPC - QUIE

Green indicator light : light ON or ﬂashing

light =



Light OFF =



anti-corrosion protection

defect : replace the battery NIMH 9V. If the

defect goes on, contact your installer.

Orange indicator light:

Light ON= under heating

Light OFF = out of heating

If connected to the mains with a dual timer schedule

or exclusive night-time schedule (only for models

with battery), the green indicator light switches on

but is very weak for the ﬁrst 48 hours in accordance

with the charge status of the battery. Check the

indication light after 48 hours of operation.

In order to guarantee full boiler

protection (green light illuminated),

any faulty batteries must be replaced.

If the batteries are not replaced, the guarantee

will become void. It makes good sense to replace

them once they have been used for one or two

years.

MAINTENANCE AND REPAIRS

1. Maintenance

Empty the appliance annually (twice a year if the

water has been treated with a softening agent)

in order to:

1. check the condition of the magnesium anode;

2. remove all deposits inside the boiler.

We strongly recommend that the performance

of the water softener is checked regularly. The

residual hardness cannot be lower than 15ºf.

A water hardness level which is too low will

cause the guarantee to become void.

1.1. Emptying

➢ Cut off the electricity supply before performing

any work on the appliance.

➢ Shut off the cold water supply at the inlet.

➢ Open the hot water tap to draw water.

➢ Open the emptying valve on the safety assembly

and the water will ﬂow out of the drainage hole.

1.2. Build-up removal – Checking the anode

➢ Empty the appliance (see above).

➢ Remove the protection element and unscrew

the base (some residual water may leak out).

➢ Clean the boiler: without using metal objects

or chemical agents, remove any build-up on

electrical elements or on the bush (steatite), on

the corresponding casing and on the base of the

boiler.

➢ If a magnesium anode is used, check its

condition: the magnesium anode is consumed

progressively in accordance with the water quality,

in order to prevent corrosion of the boiler. If the

diameter is smaller than 15 mm (for the armoured

range) / 10 mm (for the steatite range), or if the total

volume is lower than 50% of the initial volume, the

anode should be replaced.

➢ Use a new seal every time the base is

replaced after being removed.

➢ When screwing in the bolts

again, use a “cross-

tightening” technique. The tightening torque should

be between 7 and 10 Nm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston STEA-serie Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info