Bedienungsanleitung Aritech ATS1100 (Seite 1 von 12) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

702270

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite



1 2 3 4

 SW2

1 2 3 4

+12 0V D+ D- IN OUT

ATS Control Panel

(J10)





SW1 DIP Switch

RAS 1

2 3 4 1

2 3

RAS 2 RAS 3

2 3 4

RAS 4

RAS 5 RAS 6

2 3 4 1

2 3 4

RAS 7

2 3 4

RAS 8

2 3 4 1

2 3 4

RAS 15

2 3 4

RAS 16 RAS 13 RAS 14

RAS 9

2 3 4 1

2 3 4

RAS 10 RAS 11

2 3 4

RAS 12

8-Area LCD RAS

MOUNTING THE UNIT

Please make sure the keypad is mounted on a flat surface, in

order to prevent any incorrect tamper switch actuations.

Attach the mounting box using screws. Secure the PCB with the

screw supplied. Secure the keypad cover with the screw supplied.

When a pry-off tamper is required, use a screw in the back of the

keypad (see figure A, ).

CONNECTING THE KEYPAD TO A CONTROL PANEL (FIGURE A)

 Refer to the ATS control panel installation guide for instructions.

LEDS (SEE FIGURE A)

Rx LED flashes to indicate polling data is being received on

the system databus from the ATS control panel. If the

LED does not flash the control panel is not operational

or the databus is faulty (usually cabling).

Tx LED flashes to indicate the arming station (RAS) is

replying to polling from the ATS control panel. If the Rx

(Rx0) LED flashes but the Tx (Tx0) LED does not, the

arming station (RAS) is not programmed to be polled in

the control panel or is addressed incorrectly.

LED INDICATIONS ON KEYPAD

Area 8 red LED’s illuminate when area 1-8 (or 9-16) are

armed. Will blink (armed) or flash (disarmed) on alarm.

Mains Green LED illuminates if 230 VAC mains power is

available.

Alarm Red LED illuminates on any alarm in an area assigned to

the keypad.

Fault Yellow LED illuminates on fault’s in the system.

COMMS CONNECTIONS (FIGURE A, TERMINAL J3)

Power supply. If the distance between the arming station

and the control panel does not exceed 100m, then the

arming station can be powered using the Comms + and

– from the control panel. Otherwise use AUX PWR from

DGP’s or an auxiliary power supply.

D+ Data positive and data negative connection of the

databus.

D - Remote units can be up to 1.5 km from the

ATS control panel.

IN A request to exit button (normally open, momentary

push-button switch) can be connected across “IN” and “-

“. When pressed, this button controls the request to exit

function.

OUT Open collector output, 50 mA maximum. It is the first

output of the output control group that is assigned to this

arming station.

RAS DIP SWITCH SETTINGS (FIGURE A)

 SW1 DIP switches

These are used to identify the RAS address. See figure B for

settings.

 SW2 “A, B, C, Term”

These are used to terminate the databus and enable various other

functions, as described below:

SW2-1, A Area 9-16

OFF The 8-area LEDs display the status of areas 1 to 8.

ON The 8-area LEDs display the status of areas 9 to 16.

SW2-2, B Keypad backlight

OFF The keyboard backlight times out.

ON The keyboard backlight stays on continuously.

SW2-3, C Magnetic card format (ATS1105 only)

OFF ATS format

ON Non-ATS formats.

(e.g., credit cards, any cards with data on track 2).

SW2-4, TERM

OFF Not the last device on the databus.

ON Terminates the databus if this RAS is the last device on

the databus. See also the ATS control panel’s

installation guide.

READERS CONNECTIONS (ATS1105 ONLY) (FIGURE A, J2)

+5 V supply and data connections for ATS magnetic card

readers (ATS1105 only).

1 D1/D Read data pulse / Wiegand D1 line

2 D0/C Read clock pulse / Wiegand D0 line

3 GND (0V)

4 +5 V

5 +12 V

Additional functionality

- To adjust LCD contrast – Press Menu * and Ç or È

- To adjust buzzer volume, press Clear and Ç to increase

and È to decrease the volume

+12

ATS1100/1105

8-Area LCD RAS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1100 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info