Bedienungsanleitung Aritech ATS1110 (Seite 3 von 36) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

702271

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

System Fault Buzzer

In case a System Fault occurs (no more communication to control

panel) the text “System Fault” appears on the display and the buzzer

will be activated until any key is pressed. The setting “Auto” is used

to enable this feature for countries where this is a requirement. The

setting can also be set to “On” or “Off”. The setting can be changed

by holding the “MENU” key while momentarily pressing the “0” key.

Each next press of the 0 key selects either “Auto”, “On” or “Off”.

Function keys

F1 = ‘OPEN’ + 1

F2 = ‘OPEN’ + 2

F3 = ‘OPEN’ + 3

F4 = ‘OPEN’ + 4

TZ62 = ‘OPEN’ + 5

TZ63 = ‘OPEN’ + 6

POWER UP

Upon initial power up, the buzzer will sound two beeps indicating that

the internal non-volatile memory is OK. All of the area LEDs may

illuminate, indicating that the system is armed. All areas must be

disarmed in order to enable access to the installer programming

menu options.

TROUBLESHOOTING

General Faults

No LED or LCD display:

• Verify the +13.8 and 0V wire connections on both the RAS

and the power supply.

• Verify power output on the DGP or external power supply.

Area and Status LEDs are flashing and the LCD display reads

System Fault:

• Verify the D+ and D- wire connections (may be reversed or

open circuit).

• Verify the address DIP switches of the RAS is set to the proper

address.

• Verify that the control panel or 4-door controller DGP is polling

the RAS address.

ATS1115 or ATS1116 RAS with Smart Card reader does not

respond to a Smart Card:

• The RAS may actually be an ATS1110 or ATS1111 type that is

not fitted with a Smart Card reader.

• The Smart Card may not be programmed (blank).

RX and TX LED Indications

RX and TX LEDs are provided on the circuit board to assist in fault

diagnosis, and are visible when the rear plastic cover is removed.

Rx The yellow Rx LED flashes to indicate polling data is being

received on the system bus from the panel. If the LED does

not flash, the control panel is not operational or the bus is

faulty (usually cabling).

Tx The red Tx LED flashes to indicate the RAS is replying to

polling from the control panel. If the Rx LED flashes but the

Tx LED does not, the RAS is not programmed to be polled

in the control panel or is addressed incorrectly

PROGRAMMING MAP

1-Access LED options

0-EXIT, Menu:

LED enabled

*-Change, #-Exit

2-Night Light Options

0-Exit, Menu:

GE Security, RAS1110.V05

0-EXIT, Menu:

Night Light On

*-Change, #-Exit

3-Keypad Backlight Options

0-Exit, Menu:

Keypad Backlight On

*-Change, #-Exit

4-RTE (Egress) Control

0-Exit, Menu:

RTE Only

*-Change, #-Exit

5-Reserved

0-Exit, Menu:

6-Factory Defaults

0-Exit, Menu:

Set Factory Defaults?

*-Yes, #-No

7-Security Mode

0-Exit, Menu:

Un-Secured Mode

*-Change, #-Exit

8-Valid Card Flash

0-Exit, Menu:

Flash Enabled

*-Change, #-Exit

9-Protocol Options

0-Exit, Menu:

Wiegand

*-Change, #-Exit

10-Card Beep Options

0-Exit, Menu:

Card Beep Enabled

*-Change, #-Exit

11-Option Card

0-Exit, Menu:

Option Card Enabled

*-Change, #-Exit

12-Last Card

0-Exit, Menu:

FC=1, ID=1

#-Exit

PROGRAMMING OPTIONS

The ATS1110, ATS1111, ATS1115 and ATS1116 provide for a menu

through which a number of options can be set.

To enter the programming menu for the ATS111x keypads:

Enter menu 28 of the Control Panel installer menu.

Press 2[ENTER] followed by the RAS address selected and [ENTER]

to enter the RAS menu. The display now shows “GE Security,

RAS111x” (x is 0, 1, 5 or 6 depending on the type of keypad)

followed by the version number.

Press [ENTER] to proceed to the menu or press the menu number

followed by [ENTER] to go to a menu item directly.

Menu 1, Access LED options

Controls the blue Access LED (enabled by default). The blue Access

LED may be disabled if not required.

Menu 2, Night Light Options

A dimly lit keypad backlight provides the night-light to easily locate

the keypad in dark locations (enabled by default).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1110 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info