Bedienungsanleitung Aritech ATS1197 (Seite 4 von 8) (Englisch)

702273

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

• The yellow wire controls the LED 1 green (Disarm). Wire

grounded (0V): LED 1 green on, wire open or at +5 V to +14 V:

LED 1 off.

• Both yellow and brown wires grounded (0V), LED 1 is on yellow.

Not valid when used on GE Security products.

For one-wire LED control, the brown wire controls LED 1 green-red

dual colour.

• Grounded or 0V, LED 1 green on.

• +5 to 15V: LED 1 red is on.

• Open or high Z, or +2.5V: LED 1 off.

Menu 3, Valid Card Flash

If enabled (default), the green LED will give one short flash when the

card is badged. The panel controls subsequent flashes.

Menu 4, Night Light

A dimly lit keypad backlight provides the night-light to easily locate

the keypad in dark locations (enabled by default).

Menu 5, Protocol options

This option selects the method by which the reader sends data to the

panel. The options are Wiegand (default) or Magnetic stripe. See

option 16 for more data on transmitted data details.

Menu 6, Card Beep

If enabled (default), the beeper will give a short beep when a card is

badged. The panel controls subsequent beeper activity.

Menu 7, Watch Dog

Offline mode only. If enabled, one byte of data is sent to the host

every minute to indicate that the RAS is connected and operating

normally. If the ATS1197 tamper is active, the data byte will not be

sent (disabled by default).

Menu 8, O/C output

Select one of the following options:

• Door relay (on-line mode only) — The open collector output

activates (active low) when the door open signal is sent to the

ATS1197 (default setting).

• Tamper output (on-line or off-line modes) — The open collector

output activates (active low) when the ATS1197 Tamper is

active.

• Card data present (off-line mode only) — The open collector

output activates (active low) when the card data is being sent to

the host.

Menu 9, Option Card

This option enables (default setting) and disables the use of reader

configuration (option) cards at the reader. If an installer wishes to

prevent the modification of the reader setup by configuration card,

this option should be disabled.

Menu 10, RTE (Egress)

The RAS is fitted with Request To Exit (RTE) control (yellow wire).

The Open Collector output (violet wire) may be used to control a door

relay. RTE is only available in on-line mode.

There are three options to choose from:

• RTE Disabled. When RTE is not used, it is recommended that it

is disabled.

• RTE Only. This option requires a simple push button to be

connected to the yellow wire. A press of the button will release

the door lock relay. Used for a quick exit from an Area (enabled

by default).

• RTE Arm/Disarm. Do not use

Menu 11, Factory Defaults

This option returns all RAS settings to the factory default condition.

Menu 13, Last Card

This option displays the number of the last card badged on the

reader, in the format: Facility Code/System Code, ID Number or as

raw card data (depends on setting of security mode).

Menu 16, Security Mode

This option selects the type of user card the reader will recognise.

The reader will recognise configuration and default cards in both

modes. The possible modes are as follows:

• Unsecured Mode (default setting) — The reader will recognise

blank or un-programmed cards only, by using the card’s unique

serial number. The 4-byte security password is not used.

Unsecured mode requires the use of an expanded memory

system.

• Secured Mode — Only cards programmed on the

ATS1620/1621/1622 programmer will be recognised in this

mode. The 4-byte security password is used.

DATA TRANSMISSION

The following tables list the formats by which the card reader

transmits data, as determined by:

• Whether the reader is used on-line or off-line, and by

• Menu option 5—Protocol Options (Wiegand or Magnetic stripe),

and by

• Menu option 16—Security Mode (Secured or Unsecured).

Note: In on-line mode, select ‘Wiegand’ in menu 5 to use 26 or 27 bit

data, or select ‘Magnetic stripe’ to use 32 bit data.

On-line

Reader protocol

Card Format

Wiegand Magnetic Stripe

Secured When badged on a

reader, 26 or 27 bit

data is transmitted,

depending on whether

the card is

programmed as

Wiegand 26 bit or

Aritech Wiegand ASC.

When badged on a

reader, 32 bit data is

transmitted.

Unsecured When an unsecured card is badged on a reader

using the magnetic stripe format, 32 bit data is

transmitted.

Off-line

Reader protocol

Card Format

Wiegand Magnetic Stripe

Secured When badged on a

reader, 26 or 27 bit

data is transmitted,

depending on whether

the card is

programmed as

Wiegand 26 bit or

Aritech Wiegand ASC.

When badged on a

reader, Magnetic

stripe format data is

transmitted.

A “card present” signal

is available on the

relay output (violet

wire), if selected in

menu option 8—Open

Collector Output.

Unsecured When badged on a

reader using the

Wiegand protocol,

Aritech Wiegand ASC

data is transmitted.

When badged on a

reader using the

magnetic stripe

protocol, Magnetic

stripe data is

transmitted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1197 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info