Bedienungsanleitung Aritech ATS1235 (Seite 4 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

702279

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

4 / 32 P/N 1070346 • REV 5.0 • ISS 03OCT11

Note: The TERM jumper (terminator) can be placed on the last

device on the bus.

Wiring specifications

The ATS1235 can be located up to 1500 m from the ATS

control panel using a WCAT52/54 cable. This cable has a core

with a gauge of 24 AWG, the diameter is 0.52 mm and the

area is 0.22 mm².

Addressing ATS1235

Each wireless DGP connected to the ATS control panel bus

must identify itself to the ATS control panel with a unique

address set with the DIP switches 5 to 8 on the DGP. Table 1

below shows 15 possible wireless DGP addresses.

Table 1: Address DIP switch settings

Address Setting Address Setting

1 1000 9 1001

2 0100 10 0101

3 1100 11 1101

4 0010 12 0011

5 1010 13 1011

6 0110 14 0111

7 1110 15 1111

8 0001

See examples in Figure 4.

Note: Do not use address 0. This is reserved for factory

testing.

DIP switches 1 to 4 are not used.

Closing the ATS1235 housing

1. Replace the plastic cover.

2. Mount sensors and 868 MHz AM repeater as required.

A repeater can be added later if sensor performance or

signal strength is found to be inadequate.

Powering up the ATS1235

1. Before powering up the panel and receiver module, verify

that all wiring at the panel and ATS1235 wireless receiver

is correct.

2. Connect the panel backup battery and AC power.

Output numbering

The output numbering of a wireless DGP is in line with all

DGPs (refer to Table 2 below), but the wireless DGP has no

ysical outputs or output expansion available. However, any

available output can be programmed in the range of 1 to 255

via key fob programming in Menu 6.

Note: Remember that in standard DGP mode the first relay of

each DGP (relay 17 for DGP 1) can be used to mask

supervision on sensors by using time zones to energise/de-

energise the virtual relay (see “Menu 11, Supervision Options”

on page 7).

Table 2: Output numbering

Control panel 1–16 DGP 8 129–144

DGP 1 17–32 DGP 9 145–160

DGP 2 33–48 DGP 10 161–176

DGP 3 49–64 DGP 11 177–192

DGP 4 65–80 DGP 12 193–208

DGP 5 81–96 DGP 13 209–224

DGP 6 97–112 DGP 14 225–240

DGP 7 113–128 DGP 15 241–255

Zone numbering

The wireless DGP zone database can be set up for either 16 or

32 zones. (32 zones only applicable for Advisor Master) This

means you can add up to 16 or up to 32 wireless devices to

the DGP. If DGP 1 has been programmed with 32 zones, then

the next 16 zones (33 to 48) normally belonging to DGP 2 will

now belong to DGP 1 and the RAS display will show 17 to 48

(for details, refer to Table 3 below, and to “Menu 13, DGP

Settings” on page 7).

Table 3: Zone numbering

Control panel 1–16 DGP 8 129–144

DGP 1 17–32 DGP 9 145–160

DGP 2 33–48 DGP 10 161–176

DGP 3 49–64 DGP 11 177–192

DGP 4 65–80 DGP 12 193–208

DGP 5 81–96 DGP 13 209–224

DGP 6 97–112 DGP 14 225–240

DGP 7 113–128 DGP 15 241–255

Introduction to programming

See Figure 5.

Each sensor must be programmed into the wireless DGP

database via an ATS control panel RAS keypad. In this

procedure it is assumed that:

• Sensor / key fob documentation is available or known.

• The DIP switch address for the wireless DGP is set

correctly.

• Sensors are physically installed or mounted.

• The repeater has been installed and programmed if

required.

The specific details for each sensor need to be reviewed on

the related component sheet. In general, you need to know

that the sensor can be “learned” by the system by activating it,

for example, initiating a tamper alarm for the detectors and

door or window sensors.

See an appropriate wireless device manual to find out how to

activate a particular device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1235 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info