Bedienungsanleitung Aritech ATS1235 (Seite 7 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

702279

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

P/N 1070346 • REV 5.0 • ISS 03OCT11 7 / 32

Menu 8, Short Supervision Time

Short supervision is used to disable arming if the DGP does

not receive a supervision message from a sensor within the

short supervision time (20 minutes by default).

Menu 9, Long Supervision Time

Long supervision will set a fault condition in the panel for a

sensor/zone which supervision timer expired (2 hours by

default).

Program the supervision time to control how often the wireless

DGP checks the sensor is communicating and in range of the

wireless DGP.

Menu 10, Smoke Supervision Time

Menu 10 sets the supervision time for smoke sensors.

A smoke detector sends a supervisory signal every

63 minutes.

A Smoke supervision sets a fault condition in the panel when a

detector supervision timer expired (4 hours by default).

Program the supervision time to control how often the wireless

DGP checks that the sensor is communicating and in range of

the wireless DGP.

Menu 11, Supervision Options

The supervision function monitors sensors at the interval set

up in the previous procedure.

Long supervision and smoke supervision can be switched on

or off, or disabled by the first relay of the wireless DGP (relay

17 for DGP 1) to stop unwanted supervision failure messages.

The factory default for supervision is On.

Four-button fobs do not transmit a supervision signal; when

fobs are programmed, they automatically set supervision

to Off.

Menu 12, Receiver Sensitivity

Menu 12 is used to select the receiver sensitivity .

The sensitivity is also reduced by −6 dB in programming mode

by default. With this menu the sensitivity can be changed to

normal in programming mode.

After exit from the programming mode the sensitivity returns to

normal.

Menu 13, DGP Settings

The DGP can be configured for one of the following modes:

• Extended 16 zones

• Standard 13 + 3 zones

• Extended 32 zones

• Standard 29 + 3 zones

In the extended modes the DGP reports low battery, long or

smoke supervision, and smoke detector dirty state for each

sensor to the panel separately. This enables the panel to

handle this status information for each zone.

In the standard modes the first three zones of a DGP are

reserved to report supervision, low battery, and smoke detector

dirty state.

For example, on a DGP with address 1 the first three zones

are reserved as follows:

• Zone 17, smoke sensors dirty. If any of the learned smoke

sensors reports a dirty state, this zone is in an alarm state.

• Zone 18, supervision. If any of the learned zones is in

short supervision state then this zone alarms. If any of the

learned sensors is in long supervision or smoke

supervision state this zone is in tamper alarm state.

• Zone 19, low battery. If any zone reports a low battery

fault, this zone is in an alarm state.

Menu 14, Factory Defaults

Menu 14 allows you to reset the wireless DGP to its factory

default settings (extended mode, 16 zones).

Caution: Resetting clears the entire wireless DGP database.

Supported Sensors

• TX-1011-03-1 Wireless Slimline door/window contact,

868 MHz GEN2, white

• TX-1011-03-3 Wireless Slimline door/window contact,

868 MHz GEN2, brown

• TX-1211-03-1 Universal Transmitter, 868 MHz GEN2,

white

• TX-1211-03-3 Universal Transmitter, 868 MHz GEN2,

brown

• TX-2211-03-1 Wireless PIR motion sensor, 868 MHz

GEN2

• TX-2212-03-1 Mirror PIR, 868 MHz GEN2, Pet Immune

• TX-2411-03-1 Wireless PIR/MW motion sensor, 868 MHz

GEN2

• TX-6211-03-1 Wireless optical smoke/heat sensor,

868 MHz GEN2

• TX-6212-03-1 Wireless optical smoke/heat sensor,

868 MHz GEN2

• TX-4131-03-2 Wireless 4-button keyfob, 868 MHz GEN2

• TX-3011-03-1 868 GEN2 2-button pendant panic, white

• TX-5011-03-1 Shock sensor, 868 MHz GEN2, white

• TX-5011-03-3 Shock sensor, 868 MHz GEN2, brown

Note: The external contacts on TX-1011-03-1 and TX-1011-

03-3 are not supported in ATS1235 with firmware version 1.2

and earlier.

Specifications

Compatibility Advisor Master: ATS1235 requires

Advisor Master control panel firmware

version V04.09.16 or later.

Advisor Advanced: ATS1235 requires

Advisor Advanced control panel firmware

version MR_017.017.0067 or later.

868 MHz AM (crystal and SAW) Learn

Mode wireless sensors.

Wireless zones 16 or 32 per DGP (programmable)

Fobs 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1235 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info