Bedienungsanleitung Aritech ATS1290 (Seite 3 von 24) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Finnisch)

702281

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

• Data + power for all addressable detectors

The ATS1290 can support 16 detectors. For some modules, 2 inputs are

necessary, and therefore the expanded addressing mode could be

used to stay into the range of 32 addresses on the ATS1290.

Cable topology IADS – BUS (see fig )

 A - DGP, B - control panel

In principle, the bus topology is free. Shown are several topologies (see

figure ):

1. Distributed (all IADS modules distributed across the line).

2. Star (all modules with own branches to a star point).

3. Lumped (all IADS modules at the end).

Recommended cable type

Use cables with as low resistance and capacitance as possible.

If a shielded cable is used for the IADS bus, this must not be connected

to either earth, PID- or PID+. If connected, it would result in additional

capacity and it will reduce the distance of the IADS bus.

The Table 1 below shows the maximum cable lengths in metres for

different cable types. The number of modules and module load are

taken into account. Check the module manuals for the "Unit Load". 1

Unit Load corresponds to 300 µA typical current.

 The absolute minimum working voltage of the IADS DGP is

10.5 VDC with battery operation (measured on COMMS 12 VDC

power supply of the DGP).

Table 1. Maximum cable lengths (meters) with a minimum DGP voltage

of 10.5V

4 Wire IADS bus

External powered IADS modules

(4 wire IADS bus)

32 IADS modules:

AD011 (UL=1), AD111 (UL=2)

Cable type 2 x 0.5 mm 2 x 2 x 0.5 mm

# Wires 1 + 1 2 + 2

IADS bus 0.5 mm 1 mm

Distributed  S 1 x 800 m 1 x 1600 m

Star  T 16 x 200 m 16 x 400 m

U 1 x 80 m 1 x 880 m Lumped 

V 16 x 40 m 16 x 40 m

2 Wire IADS bus

IADS modules powered out of the IADS bus

(2 wire IADS bus)

16 IADS modules:

EV435-AD (UL=8), EV435AM-AD (UL=16)

Cable type 2 x 0.5 mm 2 x 2 x 0.5 mm

# Wires 1 + 1 2 + 2

IADS bus 0.5 mm 1 mm

Distributed  S 1 x 200 m 1 x 400 m

Star  T 16 x 200 m 16 x 400 m

U 1 x 40 m 1 x 80 m Lumped 

V 16 x 10 m 16 x 20 m

 The distances S, T, U and V are referred to in Fig .

 The power supply of conventional detectors is not taken into

account.

IADS module address setting and zone/output numbering

The address setting for the IADS module is directly linked to the zone

and output number the module will have in the control panel. IADS

module numbering starts from DIP switch setting 0.

Table 2. Address setting examples

1st DGP

address

Internal module

(e.g. EV435-AD) address

DIP switch setting on

internal module

17 0 00000000

18 1 10000000

19 2 01000000

4th DGP

address

Internal module

(e.g. EV435-AD) address

DIP switch setting on

internal module

65 0 00000000

66 1 10000000

67 2 01000000

15th DGP

address

Internal module

(e.g. EV435-AD) address

DIP switch setting on

internal module

241 0 00000000

242 1 10000000

243 2 01000000

Combine functionality to one output

For some applications, it is good practice to combine functionality to

one output to save outputs for other purposes. For example, enabling

and disabling walk test LEDs for the AD111.

Normally one output, of which can enable/disable the walk test LED, is

directly linked from the control panel to the IADS module. Each output

can control one walk test LED of one IADS module.

It is also possible to control all walk test LEDs of all AD111 by one

output. The only requirement is that the output needs to be within the

DGP range. Program the "ATS style output" for all relevant IADS

modules to one specific output. If more areas need to be controlled

separately, more outputs need to be reserved.

Learning IADS modules

IADS modules need to be recognised by the ATS1290 IADS DGP before

the device will be able to transfer status information or can be

configured by the IADS DGP.

To facilitate this, the ATS1290 IADS DGP has a jumper (JP2, fig , ).

Shorting this jumper with a screwdriver for a few seconds will start the

learn mode by which modules will become known. Any additional

settings regarding configuration of the module are available either by

jumper/DIP switch settings or via configuration menu, which is a part

of the ATS1290 menu. For more information on the available settings

of a module, see the manual of that module.

ATS1290 programming menu

The ATS1290 provides for additional settings available through the

onboard menu. To enter this menu:

• Connect the ATS1290 to the ATS control panel.

• In the ATS control panel Installation Programming menu:

o Activate polling to the ATS1290 (installer-menu 4).

o Enter installer-menu 28 – Remote Devices.

o Select 1-DGP.

o Select the ATS1290 DGP address.

You are now in the ATS1290 DGP menu.

Menu explanation

1. Status

Retrieve information regarding the status of the ATS1290.

Use the ENTER key to move through the different information screens.

1.1. Operational status

Indicates module status: DGP-Tamper, Module missing, multiple

modules, etc.

1.2. Device info

Shows in one line the number of modules known to the system, the

number of modules in alarm and the number of modules in tamper.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS1290 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info