Bedienungsanleitung Aritech ATS7200 (Seite 2 von 20) (Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch)

702287

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Voice Reporting

Module

WHAT DOES IT DO?

The ATS7200 enables event reporting by playing back pre-

recorded messages to 1, 2, 3 or 4 different reporting sites

(Central Stations). Voice reporting takes place via the built-in

dialer of the control panel (PSTN) or via the optional ISDN

module.

SINGLE AND MULTIPLE VOICE MODULE MESSAGES

A maximum of 2 voice reporting modules can be installed.

There are 8 messages per module; the leader message, the

address message and 6 alarm messages. If a second module

is installed, all 8 messages for the second module will be

alarm messages (Refer to table 1 on page 2)

MOUNTING LOCATION

The ATS7200 must be mounted inside an ATS panel housing.

Important:

1. Disconnect the mains power before opening the cabinet.

 Disconnect AC mains plug from AC mains wall

socket.

 Disconnect the mains with a dedicated circuit

breaker.

2. Disconnect the battery (when applicable).

MOUNTING THE UNIT (REF. TO FIGURE  & )

Mounting the ATS7200 into the control panel

(ATS2000/3000/4500)

1. Place the clips in the square holes (4) (use metal pillars

when available).

2. Mount the ATS7200 using screws.

Mounting the ATS7200 into the control panel

(ATS4000/2300/3300).

1. Remove the screws (1) and lift off the control panel PCB.

2. Place the extension pillars with the plastic rings on top of

the existing pillars (3).

3. Place the clips in the square holes (4).

4. Mount the ATS7200 using the screws and extension pillars

(5).

5. Place the ATS control panel PCB back into it’s original

position.

Connecting the voice module

1. Connect the flat cable (2) between the control panel

(connector J20) and the ATS7200 (connector CONN1or

CONN2).

2. Connect the telephone line to the control panel or to the

ISDN module.

DESCRIPTION OF THE ATS7200 (REF. TO FIGURE )

No. Description Function

1. CONN 1/CONN 2

(System connector)

Communicates between the

ATS7200 and the main

panel.

2. CONN 3 Used for recording and

checking messages.

3. Push button Controls recording and

checking of reporting

messages.

4. Jumpers Selects additional slave

addresses in the event that

more than one voice

reporting module is used

within the same panel.

5. Gold Cap Used for retaining recorded

messages during short

power failures.

6. LED Indicates presence of +12

VDC power.

MI ADDRESS SELECTION AND POSITIONING JUMPERS

The address of the ATS7200 on the MI-bus is determined by

three jumpers. These jumpers are placed beside the Gold cap

and are labelled A0, A1 and A2. If only one module is used, all

jumpers will be present. For the second module, jumper A0 will

be removed.

Note: Jumpers A1 and A2 are for future applications

Device Jumpers

A0 A1 A2

Module 1 I I I Default I = Inserted

Module 2 R I I R = Removed

REPORTING SEQUENCE

The ATS7200 first reports the leader message (1) followed by

one or more of the alarm messages (3 to 8) and finally the

address message (2). The leader message is repeated up to

10 times unless the user presses “0” to move over to the

actual alarm message. If the user does not press zero in time,

the panel hangs up and dials again later. When a second

ATS7200 is installed, all 8 messages of the second unit are

alarm messages. Therefore messages 3 to16 will be available

for alarm messages. (Note: The total recording time for the

eight messages is 35 sec.).

Table 1

Position Function Examples

Message1

(Leader

message)

Notifies the listener

that a voice report

message is waiting

by playing back a

number of times.

"There is an alarm.

Press ‘0’ (zero) for

details."

Message 2

(Address

message)

Specifies the

address of the

protected premises.

“….At Interlogix,

Kelvinstraat,

Weert”. Press ‘0’

(zero) to

acknowledge this

message”.

Message 3-8

(Alarm

message 1-6)

Reports different

alarm types (They

can be played back

to any MI-audio

lines

“Burglary, Front

door”.

“Tamper”

“Mains Fail”

TO RECORD A MESSAGE (RECORD MODE):

1. Prepare a list of messages before starting recording. Use

the programming sheets in tables 3 and 4.

2. Turn on the power (reconnect the mains and the battery)

and connect the telephone to CONN 3.

3. Pick up the handset of the programming telephone and

put it to your ear.

4. Press the push button next to the RJ12 connector, wait

for the beep, and start speaking.

5. Release the button only after you have finished recording

the message. (Note: In case of a mistake, release the

button for more than 10 seconds or press for less than 1

second to reset the programme and start recording

again.)

6. To record the next message, press the button again

within the 10 second time-out and speak again after the

beep.

7. Repeat steps 3 and 4 until you have recorded all 8

messages.

PLAYBACK THE RECORDED MESSAGES (CHECK MODE):

1. Press the push button for less than one second.

(Important: If it is pressed for more than 1 second, you

go back into programming mode.)

2. Listen to the messages that you have been recorded.

Attention: At the end of either Record mode or Check

mode, there will be 7 beeps to indicate that the module is

now available for event reporting.

PROGRAMMING THE ADVISOR MASTER

After recording the messages, program the Advisor Master by

selecting the Voice protocol for 1 to 4 Central Stations (CS).

Aritech ATS7200 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info