Bedienungsanleitung Aritech ATS7300 (Seite 1 von 20) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Norwegisch)

702288

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

NC OC

Gouvars, Frederique (IndSys, GE Interlogix)

GSM Module

WHAT DOES IT DO?

The ATS7300 enables alarm reporting via GSM. All reporting

formats available through PSTN are fully functional, including voice

reporting or audio listen-in.The GSM module can be used for

primary reporting as well as back-up reporting (using multiple

central stations).

The ATS7300 has a provision to establish a reliable connection for

remote up-/downloading to and from the ATS panel. In data mode

the GSM module even can establish a connection up to 4800 baud

(for more details and programming options see ATS2000 / 3000 /

4000 Programming manual). A general fault indicator is available

(OC) to indicate if the battery is present, the battery fuse is ok and

the GSM network is detected.

IMPORTANT:

 Disable PIN code request on your SIM card (via

any mobile telephone)

 For proper operation a GSM card with subscription

is mandatory (NOT pre-paid).

 The ATS7300 will only operate (dial/answer) when

connected to the home network.

 A GSM module during operation can require a

maximum of 2A peak current; the back-up battery

normally wired to the control panel is now also

wired to the GSM module. The GSM module

checks the battery operation and disconnects the

battery when the battery voltage drops below 9

volts to preserve the battery (deep discharge

protection)

 Make sure the antenna itself is placed outside the

control panel.



To do up/download via the GSM module, use a SIM

card that has fax and data enabled.

MOUNTING LOCATION

The ATS7300 must be mounted inside an ATS panel housing.

Important:

1. Disconnect the mains power before opening the cabinet.

 Disconnect AC mains plug from AC mains wall socket.

 Disconnect the mains with a dedicated circuit breaker.

2. Disconnect the battery (when applicable).

MOUNTING THE UNIT

Mounting the ATS7300 into the control panel (ATS4000, Ref.

to figure ).

1. Remove the screws  and lift off the control panel PCB.

2. Place the extension pillars with the plastic rings on top of the

existing pillars .

3. Place the clips in the square holes .

4. Mount the ATS7300 using the screws and extension pillars .

5. Place the ATS control panel PCB back into its original position.

Mounting the ATS7300 into the control panel

(ATS2000/3000/4500, Ref. to figure )

1. Place the clips in the square holes  (use metal pillars when

available).

2. Mount the ATS7300 using screws.

Connecting the GSM module

Disconnect AC mains plug from AC mains wall socket

1. Remove the battery wires that run from the battery to the

control panel.

2. Add the blue “tap connectors” to the red and blue (or black)

battery leads.

3. Connect the additional wires, which will be clamped to the

GSM module.

4. Before clamping ensure that the battery leads will reach the

GMS module as well as the battery.

5. Connect the red wire to BATT IN + and the battery.

6. Connect the blue (or black) wire to BATT IN – and the battery.







ATS7300

GSM Module

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech ATS7300 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info