Bedienungsanleitung Aritech CS275 (Seite 12 von 167) (Englisch)

557694

Zoom out

Zoom in

Vorherige Seite

1/167

Nächste Seite

CS175-275-575-875 Installation Guide

through the on-board electronic output, must be of SELV (Safety extra-low voltage)

operating circuit.

•

Use a relay with good insulation between the contacts and the coil.

•

Place a suppression diode, for example, a 1N4001, across the relay coil.

•

Relays connected to open collector outputs of the alarm system should be rated

at 12 volts DC with a coil impedance greater than 400 Ohms.

5. The remote bus cable is used for communication between the control panel and the

keypads/expanders. The greatest care should be taken when installing this cable.

Never split it into separate cables. Do not use cables with wires that are used for

telephone connections or for switching, for example, flashing LEDs, sirens or relays.

6. Avoid cable ducts and cableways that contain mains power cables. This is

particularly important when such ducts contain cables supplying electric motors,

fluorescent lights or three-phase power. If this is not possible, shielded cable should

be used and the cable should be earthed at the control panel end only.

7. If the upper and/or lower cabinet entry cable holes are used to route wiring into the

control panel, always use a proper pipe fitting system by means of appropriate

conduit and junction box. Use only materials of suitable flammability class (HB or

better).

8. For mains power connection, use the mains connector terminal either through a

permanent wiring or a flexible mains cable to an earthed mains outlet. Always use

cable ties to fix mains cable at the dedicated fixing point provided near the mains

terminal connector.

•

For permanent fixed wiring, insert an easily accessible, dedicated bipolar circuit

breaker in the power distribution network.

•

Do not solder the end of a stranded conductor at places where the conductor is

subject to a contact pressure, unless the method of clamping reduces the risk of

a bad contact due to cold flow of the solder.

4.3 Basic installation procedure

You should first identify a suitable place for the control unit. This must be convenient to a

mains supply and a telephone connection.

You must then:

1. Mount the sensors, keypads, control unit, smoke detectors and sounders.

2. Connect all modules and keypads to the keypad bus, making sure to set the DIP

switches on the modules and record the module addresses. These are needed

later.

3. Connect the battery and the mains power. The control panel will not start if only

the battery is connected.

4. Program all keypads with their keypad number and partition number using  94.

See

Setting keypad options

on page 40 for more information.

5. Set the options on each keypad.

6. Once all keypads have been programmed, you can either enter and exit

programming mode to initialise the modules and keypads, or continue by

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech CS275 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Aritech CS275

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info