Bedienungsanleitung Aritech CS575 (Seite 156 von 167) (Englisch)

557695

156

Zoom out

Zoom in

Vorherige Seite

1/167

Nächste Seite

156

CS175-275-575-875 Installation Guide

Force arming

Arms the security system when a number of zones are open without inhibiting

each one individually. When enabled, the CSx75 can be force armed with

zones violated. Under this condition, if a force armable zone is not secure, the

Ready LED flashes. At the end of the exit delay, these zones are bypassed. If

these zones are secured any time during the arming cycle, they are

unbypassed and active in the system. If Bypass Report is enabled, the force

arming zones can be programmed to report bypass when they are force

armed (default), or to not report bypass even if Bypass Report is enabled.

See

Location 51

on page 70 and

Location 127

Location 206

, starting on

page 80, for more information.)

Group bypass

A designated group of zones can be programmed to bypass by pressing

Bypass-0-Bypass-Bypass prior to arming.

See

Location 127

Location 206

, starting on page 80, for more information.

Inhibited zones

Zones that are left open when the rest of the system is armed. They can be

entered without triggering an alarm.

Internal event Log

A list of events that have occurred in the security system. They are held in a

sequential event buffer with a time and date stamp. Up to 256 events are kept

in the rolling log. The log is never full, but overwrites the oldest entries with

new data. These events can later be viewed through downloading. All

reportable events report to the log.

Keypad activated panics

The CSx75 has three keypad activated panics that send reports to the central

station: Auxiliary 1, Auxiliary 2 and Keypad Panic. Auxiliary 1 activates the

steady siren, Auxiliary 2 sounds the keypad and Keypad Panic can be

programmed to be silent or audible (sound siren).

See

Location 34

on page 65 for more information.

Keypad sounder control

The CSx75 can be programmed to sound the keypad sounder for certain

events.

See

Location 49

on page 69 for more information.

Keypad tamper

If enabled, the CSx75 disables the keypad for 60 seconds and sends a tamper

signal to the central station if 30 keypresses are entered without producing a

valid code.

See

Location 34

on page 65 for more information.

Keyswitch

A mechanical device that can turn the system on or off without a code.

The keyswitch is normally placed outside the protected premises to effect

arming and disarming. A keyswitch must be a single pole (two-state) switch,

which is connected to a zone. It can be pulsed or normally closed.

Keyswitch arm/disarm

Any zone on the CSx75 can be programmed as a keyswitch zone. If this is

done, a momentary short on this zone arms/disarms the control. If

opening/closing reports are sent, the user code is 99.

See

Location 36

on page 67 for more information.

Keyswitch zone type

A keyswitch zone is used to arm and disarm the control unit.

Keyswitch activation immediately arms the control unit if the control unit is

disarmed. No exit time is allowed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech CS575 Seite 156

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Aritech CS575

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info