Bedienungsanleitung Aritech PB601 (Seite 4 von 16) (Englisch, Französisch, Schwedisch)

702729

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

- 4 -

INSTALLATION I NSTRUCTIONS

1. PARTS DESCRIPTION (FIGURE )

The product is shipped with the following items. Please check that they

are all included.

1. Cover; 2. Horizontal fine adjustment screw; 3. Vertical adjustment

screw; 4. Terminals; 5. Tamper switch (receiver only); 6. Gain lock

switch (receiver only); 7. Function indications (see figure  below);

8. Mirror; 9. View finder; 10. Adjustment dial; 11. Shading plate.

12. Mounting plate; 13. Bracket; 14. 8 tapping screws (Ø 4 x 30);

15. 8 oval countersunk head screws.

Figure : Functions/indications of transmitter (TX) and receiver (RX)

1. Operation LED; 2. Beam power (H set at factory); 3. Beam channel

(channel 1 set at factory); 4. Sensitivity attenuation LED; 5. Alarm LED;

6. Beep (alignment tome) switch (OFF set at factory); 7. Response time

adjustment (50 msec. set at factory); 8. Monitor jack; 9. Memory LED;

10. Beam channel (frequency 1-4, channel 1 set at factory);

11. Environmental output selector (N/C set at factory); 12. Memory

selector (manual set at factory); 13. Remote-manual memory logic

switch (L set at factory); 14. Environmental output terminal;

15. Remote control input

terminal.

2. INSTALLING THE SENSORS

Guidelines when installing sensors

Figure : Dos and Donts on where to install the sensor. No obstruc-

tions (consider seasonal changes). Avoid strong light. Avoid splashing

the unit. Avoid unstable ground.

Figure : Calculating beam expansion (B). (A= protection distance) The

beam spread of each model type must be considered in order to avoid

potential reflection from the ground surface or nearby objects.

Figure : Recommended installation height.

Wiring the system

Connect power to both the transmitter and receiver. The wiring

depends on the number of sensors or zones. Wire size also depends

on the distance between the sensor and the control panel/power

source. The wiring must comply with NFPA-70 of the National Electrical

Code.

CAUTION: The signal output on the receiver cannot be used

independently for the upper/lower optics, only as a set. Outdoor

wiring should be in PVC if used below ground or use a burial

cable. Use conduit for above-ground wiring.

Figure : Examples of wiring.

Example 1: Standard connection.

Example 2: When two or more sensors are connected on the same

zone.

Example 3: When two or more sensors are on separate zones.

Example 4: Two-stacked standard connection.

Example 5: When the environmental module and manual alarm memory

are used.

Note: Refer to section 5 Function Descriptions for selecting the

beam frequency.

Figure : Wiring distance between the sensor and the control panel

(m)

Note 1: The maximum wiring distance when two or more sets are

connected is the value shown divided by the number of sets.

Note 2: The signal line can be wired up to approximately 1000 m

with AWG22 (diameter 0.65 mm) telephone wire.

Standby battery: Be sure that the control panel is equipped with an

adequate standby battery and charging circuit. Use 12 V (at least) NiCd

or lead acid battery with a minimum capacity of 0.5 AH.

Arranging the terminals (Figure )

1. Environmental NC or NO, 30 VAC/VDC 1A or less; 2. Alarm memory;

3. Remote reset switch; 4. Power and terminal.

Mounting the units

The units can be easily mounted on a pole or flat surface. Using the

adjustment dial and screws, adjust the mirrors vertically (A) and

horizontally (B) so that the unit can work in all directions (figure ).

See examples 1-3.

A: Installing a wall-mounted unit

1. Remove the cover by unscrewing the screw at the base of the cover

(figure ).

2. Loosen the screws that fix the sensor body on the mounting plate and

slide the plate downwards to detach it.

3. Make the holes in the wall. Use the mounting plate as a template to mark

the screw holes. Allow 20 mm above the plate and 25 mm below the

plate for ease of detachment after installation. Figure b 1: Wood wall.

2: Concrete wall: refer to specification of the securing plug used.

4. Install the sensor (figure c)

- Insert the mounting screws, leaving 15 mm exposed.

- Install the mounting plate on the exposed screws.

- Pull the wire through.

- Tighten the screws and plug the opening of the wire hole.

- Connect the terminal.

- Attach the cover.

Note: The unit cannot be installed in an outlet box. However, the

outlet box can be used for wire-lead.

B: Installing a pole-mounted unit

1-2.Same as for wall-mounted units (figure ).

3. Make a wiring hole in the pole and pull the wire through. Place a pole

cap on top of the pole. The unit mounts to a 42-44 mm O.D. (outside

diameter) pole. Use a RIGID CONDUIT or equivalent (figure d).

Drill a 6 mm hole trough the pole where the PE beam will be mounted for

wiring. File all debris and sharp edges around the hole to prevent rough

edges from damaging the wire.

4. Install the sensor on the pole (figure e , 1: Plug opening of hole):

- Attach U-brackets to the pole and secure it to the mounting plate

with screws.

- Attach the sensor body.

- Pull the wire through and plug the opening of the wire hole.

- Connect the terminals.

- Attach the cover (break the knockouts (2) on the cover to

adapt to the configuration).

C: Installing a back-to-back pole-mounted unit

Same as for Pole Mounting described above but attach four U-brackets

to the poles in two pairs, one on top of the other, facing opposite

directions (figure f).

3. SETTING-UP FUNCTIONS AND BEAM ALIGNMENT

1. Supply power to the unit with the cover removed

2. Set the function options. Refer to section 5 Function Description for

a detailed explanation of each option.

Location Function Function switches

TX : RX Beam channel ¨ 1 channel ¨ 2 channel

(frequency) ¨ 3 channel ¨ 4 channel

TX only Beam power ¨ High ¨ Low

RX only Beep alignment tone ¨ On ¨ Off

Response time ¨ 50 msec (standard)

adjustment ¨ 300 msec ¨ 700 msec

¨ Others

Environmental output ¨ NO ¨ NC

Alarm memory ¨ Auto-reset

¨ Manual ¨ High

¨ Low

¨ Unused

3. Adjust the optical angle (figure g) by looking through the view finder

on either side of the transmitter optical unit until the receiver is visible.

Repeat the procedure for lower optical units and then repeat on the

receiver.

1. View finder; 2. Horizontal fine adjustment screw; 3. Vertical adjust-

ment screw; 4. Adjustment dial.

4. Fine tuning (figure h ). The initial beam alignment can be achieved by

using the alignment tone indicator. 1. Sensitivity attenuation LED (lights

when the beam reception is below the minimal level); 2. Alignment tone

switch; 3. Monitor jack.

4.1 Attach the shading plates (stored on the sides of both TX/RX) to the

lower optics of both TX and RX.

4.2 Turn the receiver alignment tone switch to ON.

Aritech PB601 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info