Bedienungsanleitung Aritech RF300NW8 (Seite 2 von 8) (Englisch, Italienisch)

702735

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

EN: Installation instructions

Information

This is the GE Door-Window Sensor 868 Mhz Installation

Instructions for models RF300NW8, RF300NW8B, NX-850N-I and

NX-851N-I.

The Universal Transmitter is provided with a 3-volt DL 123A

Lithium Battery and an external magnet. It contains an internal

reed switch, connections for an external open or closed contact

loop and a cover and pry off tamper switch. Two jumpers allow

you to select internal or external reed, and normally open or

closed external loop.

This Universal Transmitter is a single address device and will

transmit Alarm, Tamper, Restore, and Low Battery codes. It also

transmits a "supervisory" signal every 15 minutes to the receiver

indicating its status and presence.

Explanation of figures

1 Opening the transmitter housing

A Cover

B Slot

2 Securing the transmitter housing

3 Universal transmitter layout

C Mounting hole

D Magnet

E Aligning mark

F Battery holder

G Reed contact

H External contact input

I J2, external contact

J J3, reed contact

K Mounting hole

Jumpers

J2 - External contact (fig. 3, I) J3 - Reed contact (fig. 3, J)

Normally open (default)

Reed enabled (default)

Normally closed Reed disabled

Note: You should only use the internal reed OR the external

contact.

Installation

Recommended mounting surfaces include plastic, wooden and

aluminium door/window frames. Mounting on steel surfaces must

be avoided.

The maximum gap between the case of the transmitter and the

external magnet cannot be greater than 10 mm. For applications

requiring a gap of 10 mm or greater, use an external contact

switch connected to the external loop circuit and disable the

internal reed switch.

The Universal Transmitter should be tested at the intended

location before permanently mounting to make sure that proper

signal transmissions can be made. Consult the appropriate Control

Panel Instructions for programming and test details.

Opening, closing and mounting

To remove the sensor cover (fig. 1, A), press a small screwdriver

into the slot (fig. 1, B) at the end of the sensor while lifting the

cover. Make sure the unit and magnet can be aligned properly in

the intended mounting position and the cover can be

opened/closed after mounting. Mount the unit with the two flat

head screws (included) using the slotted mounting hole in the base

(fig. 3, K) and the mounting hole next to the tamper switch

(fig. 3, C).

Replace the cover by hooking in the "lower end" first and then

snapping the opposite cover end into place. Secure it (fig. 2) with a

self-taping screw (included).

EN-compliant installation

In order to install your wireless product according to EN50131-1,

please screw the transmitter housing according to fig. 2.

Use of the internal reed (supplied)

It is important that the magnet (fig. 3, D) is installed in such a way

that it is aligned with the mark (fig. 3, E) on the detector. Verify that

the reed switch (fig. 3, G) is enabled, and jumpers J2 (fig. 3, I) and

J3 (fig. 3, J) are in the standard position.

Use of an external contact loop

The transmitter can monitor "open circuit" or "closed circuit"

contacts but not both at the same time. Select and set Jumper

J2 (fig. 3, I) for "Normally Open" or "Normally Closed" loop. An

alarm will be transmitted when the contact opens (J2 in "Normally

Closed" position) or when the contact is closed (J2 in "Normally

Open" position). When the loop contact restores, a restore event

will be transmitted. Connect the external loop contact to the two

way screw terminal block (fig. 3, H). Jumper J2 should be set to the

"Normally Open" position (default position) if the external loop is

not used. Jumper J3 should be set to "reed disabled".

Note: In EN/INCERT approved intrusion security applications the

usage of the external input is prohibited.

Use of pry-off tamper

To allow the functioning of the pry-off tamper, you need to fit a

screw in the mounting hole (fig. 3, C). If the sensor is removed from

the wall the plastic part at the back of the base and a part of the

PCB breaks out.

Battery installation and removal

Insert the battery into the battery holder (fig. 3, F), observing

correct polarity.

Caution: Batteries can explode or cause burns if disassembled,

recharged or exposed to fire or high temperature. Please dispose

of old batteries properly.

Upon indication of low battery, please remove the battery from its

holder. Dispose the used battery according to the enclosed

WEEE instructions and/or local government authorities.

2 of 8 P/N KEM-PK27107D • REV 00.02 • ISS 24NOV08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech RF300NW8 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info