Bedienungsanleitung Aritech SHATTERPRO 3 (Seite 1 von 16) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

702740

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

SHATTERPRO 3 GLASSBREAK DETECTO R

INSTALLATION INSTRUCTIONS

- 1 -

Figure 1 - Mounting Locations

Figure 2 - Multiple Window Coverage

Microphone

LED

Figure 3 - Attaching the Cover

7. Connect the system wires to the appropriate screw terminals on the base

and tighten the screws.

8. Replace the cover as follows:

- Round housing: Line up the tabs on the base with the correspond-

ing tabs on the cover, press together and turn clockwise until the

cover snaps firmly into place. See Figure 3.

- Rectangle housing: Press the cover back down over the detector

until the cover snaps firmly into place.

9. Apply power. The red LED should flash once.

10. Test the detector. See Testing the Detector.

DESCRIPTION

The ShatterPro 3 is an acoustic glassbreak detector designed to detect

breaking glass from framed windows in the perimeter of a building. The

detector is mounted in the building interior and uses a power supply from a

12 VDC control panel. The detector is available in either a low-profile round

housing or a rectangular housing that connects easily to a single-gang box.

SELECTING A L OCATION FOR THE D ETECTOR

Mount the detector on ceilings or on walls opposite or adjacent the window

to be protected. See Figure 1. Use the following guidelines to determine the

best location to install the detector.

w Mount at least 1m from the glass windows being protected.

w Windows must be at least 30 x 60 cm square.

w Avoid locations where lined, insulating or sound deadening curtains are

used.

w Mount 30cm away from wall corners.

w Avoid locations where interior closed wooden shutters are used.

w Locate in a suitable environment as follows:

- Temperature between 0° and 50°C

- Humidity between 10 and 90% non-condensing

w Mount the detector on a stable surface up to 7.6 m from the farthest point

on the glass surface. See Figure 1.

w Avoid locations that expose the detector to possible false alarm sources

such as: Glass airlocks and vestibule areas, kitchens, residential car

garages, small utility rooms, stairwells, bathrooms, small acoustically live

rooms, air vents.

SELECTING THE B EST L OCATION FOR M ULTIPLE W INDOW

COVERAGE

The detector has a 360° coverage pattern that can cover several windows

in a single room as follows (See Figure 2):

w Draw an imaginary line from the center of each window to be covered

in towards the center of the room.

w Mount the detector as close to where the lines intersect as possible.

w Do not mount the detector at more than a 60° angle from the center of any

window to be protected.

INSTALLING THE D ETECTOR

All wiring must conform to national approvals.

Important ! If you are unsure about a location, connect a 9 V battery to the

detector and test it before permanently mounting. See Testing the Detector.

To install the detector:

1. Run the security system wiring to the detector location.

2. Remove the front cover as follows:

- Round housing: Press the release tab on the lip of the base, twist

the cover counterclockwise, and lift off.

- Rectangle housing: Gently pry up the slot on the bottom of the

cover to unlock the cover. Lift up the cover until it latches in the open

position.

3. Set the range with J3 on the circuit board. See Setting the Range.

4. Remove the appropriate wiring and mounting knockout holes from the

base. See Figure 4.

5. Pull the wires through the knockout holes and use two screws to attach

the base to the surface. Use wall anchors if necessary.

6. Strip 1 cm of insulation from each wire.

Ceiling

mount

Detector

60° max.

7.6 m

max.

7.6 m

max.

Ceiling

mount

Wall

mount

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech SHATTERPRO 3 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info