Bedienungsanleitung Artel Polifuel 12 (Seite 7 von 36) (Englisch)

694451

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Positioning and mounting the boiler

For ease of handling, transport and import of boiler, Polifuel is delivered in parts that need be mounted on

the boiler when the boiler is in the boiler room. These parts need to be installed on the boiler:

- Fan - mount on the back of boiler, is obligatory to use the flange gaskets fan, fastened using M8 bolts

and nuts. Plug-connector for power supply fan and the fan tachometer in the back of the control box. Fan

output can be mounted in any directions.

- Mechanism for grating cleaning - mount on the right side of the boiler ( in this side is pellet tank), must

be fastened using M8 bolts and nuts. After assembly, it is necessary to attach the lever burner grid with

gear motor trail. Plug-in two cables with connectors (motor and microswitches).

- Connection tubes - mount connecting tube with 4-way mixing valve to the boiler so that the T-piece is

in the upper side. On the upper connector of the T-piece incorporate safety ventilation group. On the

back of boiler were prepared two holenders for mounting connection tubes (connection tubes with 4-

way mixing valve). Be sure to use the seal for

holenders. Set

return temperature sensor in the elbow

with a socket for the sensor between the 4-way mixing valve and the boiler. It is obligatory using the

included thermal paste. Plug-in return flow sensor on the back of the box control. Connect the pump

cable with connector to the back of the control box. Mandatory set the pump on the speed 3.

- Elbow with socket for the flow sensor -must necessarily be installed after 4-way mixing valve on the

flow of the installation. Set flow sensor in the socket for sensor. It is obligatory using the included

thermal paste. Plug-in return flow sensor on the back of the box control.

- Motor device - set the motor device to the 4-way mixing valve. Plug-in the power connector on the

back of the control box.

- Pellet level in the tank sensor - mount this sensor on the back side inside of the pellet tank (see page

9). First set the plastic glass distance for sensor. After that, put the sensor on this glass. Attach the

sensor and the plastic distance with 4 screws supplied. Attach protective cover. Plug-in the cable with

connector of the pellet level

sensor

on the back of the box control.

- Pellet tank - mount pellet tank according installation manual for mounting pellet tank. Set up pellet

transporter in the pellet tank. Place the pellet tank to the boiler and set PVC tube to conveyor and tube

supply on the boiler. Set up the PVC tube so as to allow the smooth falling pellet into the burner. If

necessary, cut the PVC tube to the required length. Plug-in the power connector on the back of the

control box.

NOTE: check the tightness of connection tubes. Fasten connections binding tubes if necessary, so that

a good seal.

Technical instructions Polifuel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Artel Polifuel 12 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info