707157
83
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
8.13. Customize the Pitch Out
Click the CV Out connector on the rear-panel graphic to edit the following settings in the
MCC.
Pitch CV Output: There are two standards: Volts per Octave and Hertz per Volt.
The choice you make for this parameter will determine which of the next two
settings is available for the next parameter. Please refer to the documentation
of the hardware instrument you want to control to find out which standard it
supports.
0V MIDI note (Volts per Octave selected): The default is C-2 (MIDI note 0), but
this can be set anywhere between C-2 and G8 (MIDI note 127).
1V MIDI note (Hertz per Volt selected): The default is C0 (MIDI note 24), but this
can be set to any MIDI note number between C-2 and G8 (MIDI notes 0-127).
Note Priority: The Pitch Out connector is monophonic, and since the KeyLab mkII
is a polyphonic keyboard controller it is necessary to specify whether the control
voltage should be based on the lowest note in a chord (Low), the highest note in
a chord (High), or the most recent note played (Last).
Pitch Bend Range (Semi-tones): This parameter determines how much the
control voltage will be allowed to change when the KeyLab mk II Pitch Bend
wheel is used. You can set the range to any value between 1 semi-tone and 24
semi-tones (2 octaves).
Pitch Assignment: With this parameter you are able to specify whether the Pitch
Out connector will receive its control voltages from Part 1 or Part 2.
8.14. Customize the Gate Out
The Gate Out connector is used to convert note on / off information from the keyboard into
trigger status events. There are three options for this parameter: S-Trig, V-Trig 5V, and V-Trig
12V. Please refer to the documentation of the hardware instrument you want to control to
find out which standard it supports.
8.15. Customize the Mod 1 / Mod 2 outputs
: The Modulation outputs have the same parameters, so we'll cover them both in this section.
These two Modulation outputs provide additional continuous control voltages for use with
modular synthesizers.
Mod CV Source: The default source is keyboard velocity, but any one of the
continuous controls on the KeyLab mkII can be used. The Select buttons can be
used, too; they toggle between the maximum and minimum voltages specified
by the next parameter.
Mod CV max voltage: This allows you to specify the range of voltages that
will be generated by the selected Modulation source, with the maximum values
selectable between 1 and 10 Volts. Please refer to the documentation of the
hardware instrument you want to control to find out which voltage standard it
supports.
Arturia - User Manual KeyLab MkII - MIDI Control Center 78
83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Arturia Keylab MKII 61 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Arturia Keylab MKII 61

Arturia Keylab MKII 61 Bedienungsanleitung - Deutsch - 98 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info