Bedienungsanleitung AS Motor As 510 2T ES A (Seite 14 von 36) (Englisch)

736654

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Information on mowing

Prior to mowing, check your device for com-

pleteness, proper functioning, and cleanliness.

A dirty ventilation grid causes overheating of

the engine, this can damage the engine. A dirty

protective grid on the silencer poses a fire haz-

ard.

For your grass to grow beautiful and thick,

mow frequently and keep the grass short. Do

not mow your lawn too low in dry and hot con-

ditions because the lawn is susceptible to sun

and heat damage and will look unsightly!

Only mow with a sharp and undamaged blade

so that the blades of grass do not fray. Have

the blade sharpened and balanced regularly

(authorised service centre).

Do not mow when the grass is wet or when it is

raining. The turf may be damaged and there is

a danger of slipping!

Turn the device around only in already mown

sections. Do not leave the device unattended

while the engine is running.

To evenly distribute grass remains and to

achieve an even cutting height, we recom-

mend, for flat terrain, to proceed according to

the illustrated mowing pattern.

A mulching mower shreds the clippings better

and finer than a conventional mowers. For an

optimal cutting pattern, please heed the follow-

ing recommendations.

Recommendations for mowing with

mulching mowers:

– Mow only 1/3 of the grass height.

– Do not set the brush height to the lowest po-

sition. Recommendation: 50-60mm.

– Work under dry conditions.

– Start with slow speed.

– The slower you drive the better the cutting

result.

– If the grass is too high, you should mow in

maximum cutting height first and later mow

again in the recommended cutting height.

– If clumps form or the mulching layer is too

thick, the air exchange of the soil can be re-

stricted. Areas of rot can result.

Recommendations for using the side

discharge for mowers with 2in1 function:

– You can mow higher and thicker grass with

the side discharge if perfect mulching is not

possible any longer.

– The cut grass is ejected quicker and the

mower does not clog.

– Disadvantage: Visible cut grass on the lawn.

No mulching function. It is only possible on

the left side to mow close to the edge.

Prior to starting

Fuel used (2-stroke devices)

The engine must be run on a mixture of petrol

and two-stroke oil.

For possible mixing ratios, see chapter Mixing

ratios fuel.

Use unleaded petrol (octane rating at least

ROZ 91). You can use E10 petrol. Do not store

E10 petrol longer than 30 days. Do not use

fuels with more than 10 % ethanol (e.g. E15,

E85).

Only use fully synthetic two-stroke oil intended

for mixing in ratio 1:50. Do not use any mineral

two-stroke oil.

AS-Motor recommendation:

Fully synthetic two-stroke oil TITAN 2T 100S in

ratio 1:100.

Your benefits:

– Halve oil consumption compared to 1:50 -

therefore more environmentally and cost

friendly.

– Optimum protection of the engine for a long

service life.

– Low engine wear.

– Maximum engine performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AS Motor As 510 2T ES A Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AS Motor As 510 2T ES A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info