Bedienungsanleitung AS Motor AS 940 Sherpa 4 WD RC (Seite 34 von 60) (Englisch)

736695

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Transport

Emergency stop in the RC mode

Causes of the Emergency stop

– There is a driver in the driver’s seat.

– The transmitter is in the transmitter holder.

– Loss of radio contact between transmitter and receiver.

– Press the Emergency Stop switch on the device.

– The device has tipped.

Notice: When the control detects an error, the error code is

displayed. For meaning of this code, see chapter Error

codes.

Consequences of an Emergency Stop

The device is brought into a safe state.

– Blade is disengaged.

– Engine is switched off.

– Drive goes to neutral position, the parking brake is active.

– Status indicators go on.

– The control function of the transmitter is switched off.

Procedure after an Emergency stop

Fig.25:

After an Emergency Stop, the following starting procedure

must be carried out.

1. Check and eliminate the cause for the Emergency Stop.

2. Switch off the transmitter by pressing the start-stop

switch(1) and wait 5seconds.

3. Turn the start-stop switch (1) clockwise to switch on the

transmitter.

4. Wait until the horn of the device sounds once.

ð In the display (16) the frequency number is briefly dis-

played.

5. The status indicators on the device and on the transmit-

ter(15) go out.

6. Press the button “Horn” (4) to get the device ready for op-

eration.

ð The horn signals that the device is ready for opera-

tion.

7. The blade is disengaged in case of an Emergency Stop.

However, the toggle switch “Blade clutch“ (8) remains in

the position that was selected last. Therefore, set the

toggle switch “Blade clutch“ (8) manually to “0”.

Transport

Transport the device on a freight vehicle or a trailer which is

designed for a carrying capacity of at least as great as the

empty weight of the device.

Transport on pallets

For transport over short distances, use a fork lift or a lift truck.

For longer distances, load the device with a fork lift onto a

freight vehicle or trailer.

The user must be authorised to operate a fork lift. When the

machine is lifted, all persons must step away from the work-

ing area of the fork lift.

Notice! Drive the fork lift completely under the longitudinal

beams of the wooden pallets.

Transport of ready-to-use device

Warning

Risk of injury due to the heavy weight of the device. The

device can fall over and fall down and cause severe injur-

ies.

► Observe the following notices.

Do not stay in the tilting area of the device.

Prior to each transport, let the device cool down for at least

20 minutes. Close the fuel valve and the tank ventilation.

Use suitable ramps for loading that

– can carry the empty weight of the device + 200 kg.

– are wider than the device.

– have a slip-free surface.

Notice

Risk of damage due to incorrect fastening of straps.

► Fasten the straps only at the points shown in the figure.

► Do not overtighten the straps.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AS Motor AS 940 Sherpa 4 WD RC Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AS Motor AS 940 Sherpa 4 WD RC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info