Bedienungsanleitung AS Motor AS 940 Sherpa 4 WD RC (Seite 37 von 60) (Englisch)

736695

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Maintenance

The engine does not start

1. Press the button “Horn/Acknowledge”(4) and “Engine

start” (5) simultaneously.

ð The engine starts automatically, it is possible that the

blade is turning.

ð You can drive for 3 minutes.

Notice: If the engine does not start, rescue with the emer-

gency driving program is not possible.

Finishing the emergency driving programme

Press the start-stop switch(1) to finish the emergency driving

programme.

Maintenance

Warning

Risk of injury due to unexpected movement. When inspec-

tions are carried out, the device can move unexpectedly.

► Make sure that no persons or objects are in the danger

area of the blade.

► Immediately press the start-stop switch on the Remote

Control Transmitter to prevent the device from moving.

► Make sure that no further hazards result from an unex-

pected movement.

Warning

Risk of injury during maintenance and cleaning work when

the engine is running.

► Perform maintenance tasks only then with a running en-

gine if this is required in the Maintenance table.

Warning

Danger of poisoning due to poisonous exhaust gases.

► Do not operate the engine in closed or insufficiently

ventilated rooms.

► Please observe the safety instruction regarding the

poisoning risk.

Prior to all maintenance and cleaning work when the engine

is not running:

1. Let the device cool down for at least 20 minutes.

2. Close the fuel valve and the tank ventilation.

3. Press the start-stop switch on the transmitter and remove

the key.

4. Switch off the device using the main switch.

Improper maintenance can make the device unsafe for oper-

ation and result in accidents. Regular maintenance keeps

your device ready for use.

Service the device according to the following maintenance in-

structions.

Contact an authorised service centre if problems during

maintenance occur or if you determine deficiencies during

one of the following inspections.

Maintenance and cleaning position

Warning

Risk of injury due to the heavy weight of the device. The

device can fall over and fall down and cause severe injur-

ies.

► Observe the following notices.

To perform maintenance, repair or cleaning tasks at the bot-

tom of the device, you can lift or tilt the device.

– Lift the device only when on level and firm terrain.

– Use only lifting gear or ramps that are suitable for the

weight of the device.

– Attach the lifting gear only to the main frame because only

the main frame can carry the weight.

– Secure the device always against tilting, falling down or

slipping.

– Do not stay in the tilting area of the device.

– Do not tilt the device more than indicated in the safety in-

structions regarding driving on the slope. Otherwise the

device can tilt and the device can be damaged or contam-

inations can occur due to leaking fluid.

– Do not carry out tasks that can result in tilting, falling down

or slipping of the device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AS Motor AS 940 Sherpa 4 WD RC Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von AS Motor AS 940 Sherpa 4 WD RC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info