Bedienungsanleitung Ascent Delta Wireless (Seite 2 von 2) (Englisch)

637178

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

STEP 2: Repeat this sequence until the correct wheel size

has been entered. Then press the LEFT button to advance

to the second wheel size setting screen (b2).

STEP 3: The left-most digit will flash. Press the RIGHT

button to adjust the flashing digit. Press the LEFT button

to advance to the next flashing digit.

STEP 4: Repeat this sequence until the second wheel size

has been entered. Then press the LEFT button to

advance to the odometer programming screen for the

first wheel size.

PROGRAM THE ODOMETER

STEP 1: After programming both wheel sizes, the

computer will automatically advance to the odometer

setting screen for the first wheel size. (If you don’t wish

to program the odometer, press the SET button on the

underside of the computer to exit the set-up mode.) The

left-most digit will flash. Press the RIGHT button to adjust

the value. Press the LEFT button to advance to the next

flashing digit.

STEP 2: Repeat this sequence until the odometer value

for the first wheel size has been set. Then press the LEFT

button to advance to the odometer programming screen

for the second wheel size.

STEP 3: Program the odometer value for the second

wheel size as described above. Once the odometer value

has been set correctly, press the SET button on the

underside of the computer to exit the set-up mode and

return to the main display screen.

INSTALLATION

Since your Ascent computer is wireless, installation is

simple. Begin by attaching the handlebar bracket.

HANDLEBAR BRACKET INSTALLATION

The handlebar bracket can be configured for stem or

handlebar mounting. To change the configuration, remove

the assembly screw, rotate the bracket base 90° and

retighten the screw. Use the included zip-ties to attach the

bracket in the desired location as shown in Figure 3. Once

the bracket is securely installed, trim the excess zip-tie

ends with scissors or fingernail clippers.

COMPUTER HEAD INSTALLATION

Slide the computer head onto the bracket from back to

front until you hear a ‘CLICK’, indicating that the unit

is locked in the bracket. See Figure 4. To remove the

computer head, press the release tab at the front of the

bracket and slide the computer head out of the bracket.

WHEEL MAGNET AND SENSOR

INSTALLATION

STEP 1: Using the included zip-ties, loosely mount the

sensor (so that you can slide it around) to the fork blade

so that it’s on the same side of the bike as the handlebar

bracket. The battery cover on the sensor/transmitter

should face the wheel and should be attached to the

front (leading) edge of the fork blade (to avoid problems

should it ever come in contact with the spokes). See

Figure 5. The Delta Wireless transmission range is 24”

(60cm). The sensor/transmitter must be mounted within

24” of the receiver (computer head) in order for the signal

to be received.

STEP 2: Attach the wheel magnet loosely to one of the

spokes on the same side of the wheel as the sensor/

transmitter. Adjust the position of the magnet and sensor

by sliding both pieces up or down to achieve 1-3mm of

clearance between the two (1mm is about the thickness

of a penny). See Figure 6. If the magnet and sensor

are not close enough, the computer will not pick up a

reading or readings will be inconsistent and erratic. Most

problems that occur when installing a new computer are

related to magnet and sensor alignment and spacing.

STEP 3: Once the transmitter and wheel magnet are

aligned properly, securely tighten both in place and trim

the excess zip-tie ends with scissors or

fingernail clippers.

TEST OF INSTALLATION

Once installation is complete, test the unit to make sure

everything is adjusted and working properly. Pick up the

front end of the bicycle and spin the front wheel. The

computer should register a speed reading within 1-2

seconds. If not, check the alignment of the wheel magnet

and sensor, and make sure that the space between the

magnet and sensor is 3mm or less. Adjust as necessary

and re-test.

NOTE: Wireless cyclocomputers are occasionally affected

by electromagnetic interference. Common sources of

electromagnetic signals include high voltage power lines,

motor driven equipment and other wireless devices (such

as heart rate monitors). If you experience unusually high

speed readings, check your surroundings for possible

sources of electromagnetic signals and move away from

the source.

CHOOSE WHEEL SIZE

When switching your computer between bikes with

different wheel sizes, don’t forget to select the appropriate

wheel size setting (

1 or 2 ) for each bike. In the Trip

Distance/Automatic Rider Timer display screen (DST/

ATM), press and hold the RIGHT button for three seconds

to change the wheel size.

RESET DISPLAY SCREENS

PARTIAL RESET

The Delta Wireless maintains a separate memory of

Average Speed, Maximum Speed, Ride Time, Trip

Distance and Odometer for each wheel size ( 1 and 2 ).

The memory for each wheel size must be reset separately.

During a partial reset, only data for the currently

displayed wheel size will be cleared.

1. To simultaneously reset Average Speed, Maximum

Speed, Trip Distance and Ride Timer, press and hold

the LEFT and RIGHT buttons for 4 seconds in any

display screen.

2. To reset only Average Speed and Maximum Speed,

press and hold the RIGHT button for four seconds in

the AVS/MAX display screen.

3. To reset only Trip Distance, press and hold the RIGHT

button for four seconds in the DST/ODO display screen.

4. To reset only the Automatic Ride Timer, press and hold

the RIGHT button for four seconds in the CLK/ATM

display screen.

GLOBAL RESET

To reset ALL display screens for both wheel sizes and

ALL programmed settings (including Clock, Odometer

and wheel size settings), press the CLEAR button on the

underside of the computer. See Figure 7.

NOTE: Please note that entering the set-up mode (by

depressing the SET button on the underside of the

computer) will not reset the display screens or clear any

data. This means you can enter set-up mode to adjust

wheel size settings, program the odometer or change the

speed scale (miles/kilometers) without losing any data.

MAINTENANCE

LOW BATTERY INDICATOR

When the computer battery is low, the low battery

indicator will be displayed. Although this only indicates

the state of the battery in the computer head, it's

generally a good idea to replace both batteries (computer

head and sensor/transmitter) at the same time (see

"Battery Installation").

Made in China 300000000971 0708_2

Fig 3

Press to

Release

Fig 4

Bladed

Spoke

Round

Spoke

Fig 5

3mm Max

Fig 6

SET

CLEAR

Fig 7

08_Ascent_DeltaWireless_INS.indd2 2 7/15/08 4:10:38 PM

Ascent Delta Wireless Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info