Helpline No. UK/Northern Ireland 020 79176050 Helpline No. UK/Northern Ireland 020 79176050 Helpline No. UK/Northern Ireland 020 79176050 Help
Rep. Ireland 0044 20 79176050 Rep. Ireland 0044 20 79176050 Rep. Ireland 0044 20 79176050 Rep. Ireland 0044 20 79176050
Web Support krippl@krip Web Support krippl@krippl-watches.com Web Support krippl@krippl-watches.com Web Support krippl@krip
Page 6
Interval of measurement: every
Resolution: 1
Accuracy: +/-5
5.7 Light
By pressing the LIGHT/SNOOZE key the display will be lit for
approximately 5 seconds so that you can read the display on your base
station in the dark. It is not pos
display. Please note, however, that more power is required to
display which can result in shorter batter
6 Assembly
The base station can either b
kit on the back or be positioned on its stand. The external sensor all has a
wall fixing kit on the back and a retracta
7 Change battery display and changing the
batteries
7.1 Base station
7.1.1 Change battery display
Weak batteries in the base sta
display. A battery symbol appears on the display on the right next to th
internal humidity display. will only appear however when the
batteries are low.
Change battery display on the base station
7.1.2 Changing the batteries
Open the battery compartment on the back of the housing.
batteries (two x 1.5v AA batteries) correctly (note +/- polarity) and clos
the battery compartm
In the event that after changing
external humidity are not displayed on the base station, you should
remove the batteries from the ext
In addition, you can press the TX ke
to transmit the transmission signal manually. We r
not use recharg
Station.
Tip: When the batteries
must re-set the city and country data for sunrise, sunset, moonrise,
moonset and the atmospheric pres
7.2 External sensor
7.2.1 Change battery display
Weak batteries in
display. A battery symbol appears on the display on the base station on
the right next to the external
however when the batteries are
base station for the external sensor will be shown only for the currently
selected channel (= external sens
Change battery display on the base station for the external sensor
In addition, if a battery is low this can be seen
display on the external sensor.
Change battery display – external sensor
7.2.2 Changing the batteries
Open the battery compartm
small screwdriver. First push the retractable stand in the direction of the
arrow so that you can remove the battery compartment cov
batteries (two x 1.5v AAA batteries) correctly (note +/- polarity) and
close the batter
Note:
When changing the batteries take
cover seal jammed and not to lose it.
8 Declaration of conformity
R&TTE Directive 1999/5/EC
Summary of the declaration oonformity: Krippl-Watches hereby
declares that the Weather Station (item no. AUK-WS-11) conforms with
the basic requirements and other relevant conditions of the
1999/5/EC.
9 Troubleshooting
Before you make a
batteries and if necessary replac
If the external
If the external sensor no longer registers, this may be for one of the
following reasons:
- The batteries on the external sen
too weak. Replace the old batt
batteries together and proceed with the re-r
sensor as described in point 4, Putting
operation.
- The external sensor reception is i
removal of obstructions is often not possible (e.g. thermopane
glazing, walls with steel reinforcements or certain concr
compositions, steel be
between the external sensor and the base station o
extension cable (
- If by mistake the first external sens
channel or the second external sensor registers on the third
channel, remove the batteries, check th
channel selector on the back of the ex
or 3) and insert the batteries
- Two different external sensors alternately display the
temperature on one chann
external sensors, check the rel
selector on the back of the senso
the batteries again. Ev
into operation again, the in
changed (recoded)
- When external temperatures are below 0°C, the battery
performance can diminish and radio transmission can weaken.
In this event, reduce the dist
and the base station.
- If the display
temperature and the external hu
could be caused by the batteries in the base station being too
weak and therefore unable to receive th
external sensor. Ex
Interruptions to reception c
household equipment, TV and radio remote
transmitters or other external
only ‘- - - - or HHH or LLL” can be seen on the display. In
this event, hold the CHANNEL key down for approximately 5
seconds until you hear a signal t
the external sensor’s next transmission signal the current
external temperature and external humidity should be
displayed again.
Weak batteries
Replace the batteries as soon as the change battery sy
Wait for approximately 30 minutes before inser
not touch the battery contacts when inserting the
the corrosion stability of the contacts and ex
When inserting the new batteries
After changing the batteries proc described in point 4, Putting the
device into oper
Weak batteries
Replace the batteries as soon as the change battery symbol is displayed
(appears on the external sensor and the base station). When inserting the
new batteries always observe t
external sensor must be re-registered
Putting the device into operation.
Temperature tolerance
The base statiosensor have sensors which work
independently of one another.
External sensor temperature toler
Base station temperature tolerance: +/- 1°C
It is therefore possible that 2
other (and/or base station and
difference of 2°C.) In the case of marked tem
difference can be slightly higher as the ex
permanently.
Incorrect temperature displa
The temperature displacted by direct sunlight. Please
position the external sensor so that it
fluctuations, i.e. not indoors for example or in a summerhouse in the
garden.
Humidity t
The base statiosensor have sensors which work
independently of one another.
External sensor humidity tolerance: +/- 10%
Base station humidity tolerance: +/- 10%
(each related to medium humidity)
It is therefore possible that 2
other (and/or base station and external sen
difference of 20%.) In the case of marked humidity fluctuations, the
difference can be slightly higher as the ex
permanently.
Humidity di
If the humidity display permanently shows 20%, then the humidity is
below the measurable range or is 20%. Air surges can remed
Frequent air surges can cause higher humidity. Above all, in winter
humidity in livin
The radio clock is not receiving
In the event that the radio clock is
in a different locat
obstructed by structural or natural obstructions (
be impossible to receive a signal
event, which can then be used instead (see point 5.1.2, Manual
Electro-magnetic or atmospheric interruptions can also obstruct the radio
clock signal. These interruptions can be remedied usually
to a different loc
Electro-magnetic interf
If possible, do not place the base station or the extern
computers, printers, television sets, mobile telephones or radios as
devices with strong EMC rays and other radio stations can interrupt or
prevent radio reception.
Times for sunrise, sunset and moonrise and
Please note that in the summer time phase, it is not absolutely necessar
to receive a daily radio clock s
possible that there is a deviatio
times of the sun and moon (the difference between summer and
wintertime). (For help, see point 9, Troubleshooting ‘The radio clock is
not receiving a radio clock
