Bedienungsanleitung Asko w 620 (Seite 34 von 36) (Englisch)

309039

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Page 16

ELECTRICAL CONNECTIONSELECTRICAL CONNECTIONS

The machine is delivered ready-fitted with a plug and is

intended for connection to an ASKO Dryer, which is

equipped with a matching receptacle. The plug supplied

with the washer can only be used with an ASKO Dryer. If

the washer is used separately or with another dryer, it

must be on a separate 220 V single-phase circuit.

If the machine is to be used in a wet area, the supply

must be protected by a residual current device.

As supplied: 230 V, 60 Hz

2000 W heating element

15 A fuse required

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. This appliance is

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

WARNING! Improper connection of the

equipment-grounding conductor can result in a

risk of electric shock. Check with a qualified

electrician or serviceman if you are in doubt as to

whether the appliance is properly grounded.

Do not modify the plug provided with the appliance.

If it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

DRAIN OUTLET CONNECTIONDRAIN OUTLET CONNECTION

The machine is supplied with the outlet hose already

attached. The hose should be extended over a suitable

sink edge or drain pipe at a height of 24” to 36” (600

mm to 900 mm) above the floor. (The lower height is

preferable.) Make sure that the hose is not kinked.

If the hose is extended, the internal diameter of

the coupling must not be less than 1/2”.

NOTE:

WARNING!

Do not extend the drain hose higher

than 36” (900 mm).

WARNING!

Connection to a permanently wired

supply point must be made only by a

qualified electrician.

FREESTFREESTANDING INSTANDING INSTALLAALLATIONTION

The washer can be placed next to the dryer.

It is essential that the machine is leveled and the

locknuts are tight to prevent excessive vibration during

the spin cycles. Also be sure to leave a minimum of

1/2 inch (12.5 mm) of space between the washer and

the dryer.

ASKO washers can be installed beneath a cabinet or

worktop with a height of 34”. There must be a gap of

about 1/4” (.64 mm) all around the machine, including

between the rear edge of the machine top panel and

the back wall. The opening width must be at least 24”

(600 mm).

Space must also be available for the inlet and drain

hoses. See the diagram below for measurements and

positions.

BBUILUILTT-IN INST-IN INSTALLAALLATIONTION

NOTE: The height adjustment for the washer is

33-1/2” to 34-1/2” (850 mm to 876 mm).

Do not raise it higher than 34-1/2”.

STSTAACKED INSTCKED INSTALLAALLATIONTION

ASKO washers should never be stacked on a counter

or a dryer. You can, however, stack an ASKO dryer on an

ASKO washer. Refer to your Dryer Use and Care Guide

for instructions on how to do this.

If the drain outlet is higher than

24”, you will need to recess the

connections.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Asko w 620 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Asko w 620

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info