Bedienungsanleitung Aspi EF1210 (Seite 8 von 112) (Englisch)

628507

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

EF1210 U

SER

ANUAL

UICK

NSTALLATION

Installation of the EF1210 involves two procedures: hardware installation, and cali-

bration.

ARDWARE

NSTALLATION

Hardware installation involves the following steps:

1. Set rear panel DIP switches to select Line or Mic level and enable phantom

power for each microphone input channel, and to select ASPI Bus Device ID if

necessary. See “Configuration” on page 15.

2. Connect input and output signals (See “Connecting the EF1210 to other equip-

ment” on page 19):

• Connect the 8 Mic/Line Inputs to microphones.

• Connect the 8 Line Outputs to the inputs of a mixer.

• Turn off Phantom Power on automixer.

• Connect Zone Output(s) to amplifier(s) or powered loudspeaker(s).

• Connect AEC Reference Inputs to the T

AEC output of an EF200 or to the

output of a CODEC.

• If you wish to use the EF1210’s built in Playback/Record mixer feature, con-

nect A

MIX

, A

, T

CODEC, and R

as directed in “Playback/

Record” on page 22.

3. If you are using an RS232 remote control device, connect it to the RS-232

EMOTE

ONTROL

port; if you are controlling multiple ASPI devices, connect

them using the ASPI Bus ports (See “Connecting the ASPI Bus” on page 26).

4. Connect the external power supply.

ALIBRATION

Calibration of the EF1210 involves a sequence of five calibration steps to configure

the input and output levels of the EF1210 to match those of the equipment to which it

is connected. The EF1210 can be calibrated either from the front panel or by using a

computer. Please refer to “Calibration” on page 27 for more detailed information on

the Calibration procedure. Correct calibration is essential for satisfactory operation of

the EF1210, so please take the time to familiarize yourself with the details of the Cal-

ibration procedure by reading “Calibration” on page 27.

For front panel calibration, enter Calibration mode by pressing and holding the A

EVEL

ETUP

and I

NPUT

ELECT

front panel buttons for 2 seconds. In Calibration

mode, the S

ETUP

LED will blink to let you know which setup step you are currently

executing. Press the A

EVEL

ETUP

button to move from one Calibration step

to the next. When you have finished Calibration step 5, press the A

EVEL

ETUP

button again to exit Calibration mode; any changes that you made will be

saved as the default power-on settings when you exit the Calibration procedure.

Caution!

The EF1210 is designed to maintain a 1/4” (6.35 mm) air circula-

tion clearance above the enclosure. Do not stack or install

EF1210s in such a way as to defeat this clearance, block the side

vent holes, or otherwise impede air circulation around the

EF1210.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aspi EF1210 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Aspi EF1210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info