628507
36
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
EF1210 U
SER
M
ANUAL
34 http://www.aspi.com Copyright © 1999, All Rights Reserved
CODEC signal. No other calibration is necessary for Playback/Record.
The T
O
CODEC signal may be adjusted to match the level required by your
codec (or other remote terminal equipment) input.
4.2. Press the L
EVEL
A
DJUST
D
OWN
button to set the T
O
CODEC level to -10 dBV.
Press the L
EVEL
A
DJUST
U
P
button to set the T
O
CODEC level to 0dBu. More
precise level adjustments can be made with RS-232 commands (See the GAINC
command on page 62 in the Command Set Reference.).
Refer to Figure 14 on page 34.
C
ALIBRATION
S
TEP
5: Z
ONE
/R
EFERENCE
S
ETUP
5.1. Enter Zone/Reference Setup mode by pressing A
UX
I
N
L
EVEL
/S
ETUP
after step-
ping through the normal configuration sequence. For Calibration Step 5, the
S
ETUP
LED will blink five times per period.
If you are only using a single zone, you may omit this step.
During Calibration Step 5, you may set the EF1210 to use different AEC Refer-
ence Inputs for each channel. The reference signal used with channel 1 will be
used as Zone A output, and the reference used with channel 8 will be used as
Zone B output. Microphones on the input channels must be placed in the sound
field of the appropriate Zone output for the EF1210 to operate correctly; other-
wise echoes will not be cancelled. In other words, if for example the microphone
on channel 3 is in the soundfield of the loudspeaker connected to the Zone B out-
Note.
You may skip this step if you are not using playback and record on
the EF1210
Figure 14.
Calibrating for playback and record.
-12 -7 -3 0 3 20 dB -12 -7 -3 0 3 20
AUX IN
LEVEL
REF
SELECT
INPUT
SELECT
SETUP
AEC
A
AEC
B
12345678
INPUTPOWER REMOTE
MUTE
ALL
LEVEL
ADJUST
SETUP
STEP 4.2a:
press to set
CODEC OUT
level to -10
dBV
STEP 4.2b:
press to set
CODEC OUT
level to 0 dBu
LED blinks four
times for record
and playback
calibration
36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Aspi EF1210 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Aspi EF1210

Aspi EF1210 Zusatzinformation - Englisch - 3 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info