691098

Assault AirRunner Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
ASSEMBLY
Introduction
• The Assault Fitness AirRunner treadmill requires only minor assembly. All tools required to complete the initial
setup and assembly have been included in the Assembly Hardware Kit.
• Remove the unit and all parts from the carton and packaging. Conrm all parts shown in the section titles As
Shipped are included before attempting assembly of the AirRunner.
Assembly Step One: Upright Installation
• Locate the Speed Sensor Cable – Lower (549a) and ensure the end/connector is extending from the main
frame.
• Raise the Upright – Left vertically, ensuring the Keyholes are located at the bottom. Align the Upright - Left
keyholes with the two posts located on the main frame. This will support the upright while completing the
installation.
• Connect the Speed Sensor – Lower (549a) and Speed Sensor Cable – Middle (560b) connectors rmly.
• Locate three (3) sets of #534 Hex Screws and #562 Flat Washers, and loosely thread each assembly through the
Left Upright and into the main frame. Tighten the screws rmly.
• Hang the Upright – Right keyholes onto the Main Frame posts and install the remaining three (3) sets of #534
Hex Screws and #562 Flat Washers.
6
Console (514)
Console Cover
- Right Inner (530)
Console Cover
- Right Outer (531)
Upright - Left
(502)
Upright
- Right (503)
Sidecase Center Cover
- Right (510)
Sidecase Center Cover
- Left (507)
Main Assembly (A)
Console Cover
- Left Inner (529)
Console Cover
- Left Outer
(528)
Handrail (504)
Speed Sensor Cable - Upper (559a)
Speed Sensor
Cable
- Middle (560a)
Speed Sensor
Cable - Middle
(560b)
Speed Sensor
Cable - Upper (559b)
Speed Sensor
Cable - Lower (560a)
Console Cable
(514a)
ASSEMBLY TOOLS
AA Alkaine
Batteries
4 pieces
4mm
Hex Wrench
5mm
Hex Wrench
13/16mm
Open-Ended
Wrench
Button Head Hex Screw M8 x 20mm (535)
Hex Screw M10 x 75mm (534)
HARDWARE DESCRIPTION DRAWING QUANTITY
Flat Washer Ø20OD x 11ID x 1.5t (562)
Phillips Head Screw M4.2 x 13mm (538)
6
6
12
AS SHIPPED
MANUAL TREADMILL
QUICK START
GUIDE
534
562
560b
560(a)
562
534
549a
Upright - Left
Upright - Right
Keyholes
Posts
507
537537
537
510
537
Upright
Assembly Step Two: Sidecase Covers
• Locate the Sidecase Center Cover - Left (507). Align the tabs locate at the top with the receivers on the installed
sidecase plastics. To install, the cover will hinge downward and snap in place. Ensure the outer surface of the cover
is ush or aligned with the adjacent plastics.
• Secure with two (2) #537 Phillips Head Screws.
• Remove the four (4) #564 Hex Screws
from the backside of the Console (514)
and set them aside.
• Connect the Console Cable (514a) and
Speed Sensor Cable – Upper (559b)
connectors and carefully tuck the excess
cable into the Handrail.
• Loosely thread the four (4) #564 Hex
Screws through the mounting plate on
the Handrail and into the backside of the
Console (514). When all four (4) screws
are installed, tighten rmly.
• With the help of a second person, support
the Handrail assembly above the uprights
and connect the Speed Sensor Cable –
Upper (559b) and Speed Sensor Cable –
Middle (560a) connectors. Carefully tuck
the connectors and excess cables into the
left Upright.
• Set the left and right Handrail brackets
inside the left and right Uprights. While
supporting the Handrail Assembly,
loosely thread three (3) #535 Button
Head Hex Screws through the left
Upright and into the Handrail bracket.
Assembly Step Four – Final Adjustments
• Identify a suitable location that is level and oers enough space for the unit with the minimum required free
space. It is recommended that the AirRunner be sited with a minimum of 0.5 meters (19.7 in.) of clearance from
the nearest walls or other equipment to the left, right and front of the unit. A minimum of 2.0m (79”) of clearance
should be maintained to the rear of the AirRunner.
CAUTION: THIS TREADMILL IS HEAVY. INJURY CAN OCCUR IF PROPER LIFTING TECHNIQUES
ARE NOT PRACTICED.
• To relocate, raise the rear of the unit with by grasping the transport handle and slowly rolling the AirRunner to
the desired location.
• Ensure the unit is level and does not rock by adjusting the Stabilizer Leveling Feet. Two feet are located at the rear
of the main frame. As a starting point, loosen each foot by threading the assembly downward/clockwise, and
then thread the locknuts downward (clockwise) against the base of the foot. Check the unit for stability and make
any adjustments as necessary. Once stable, lock the Stabilizer Leveling Feet in place by tightening the jamb nut
upward/counter-clockwise, against the underside of the frame to lock the current positions for each foot.
• Congratulations. The assembly of your Assault Fitness AirRunner treadmill is complete. Please read all included
information, user guides and warnings before use.
Assembly Step Three – Handrail & Console Installation
Repeat this step for the right side and tighten all six (6) screws rmly.
• Align the Console Cover – Left Outer (528) with the outside of left Handrail bracket, and thread two (2) #537
Phillips Head Screws through the handrail bracket and into the #528 Cover. Repeat this step for the right side
with Console Cover – Right Outer (531).
• Align the Console Cover – Left Inner (529) with the inside of the left Handrail bracket install two (2) #537
Phillips Head Screws through the #529 Cover and into the #528 Cover.
• Align the Console Cover – Right Inner (530) with the inside of the right Handrail bracket and install two (2)
#537 Phillips Head Screws through the #530 Cover and into the #531 Cover.
5803 Newton Drive Carlsbad, California 92008 Ph. 1.888.815.5559
For more information or questions regarding your equipment, please visit our website at
AssaultFitnessProducts.com
© Assault Fitness 2017
514a
514
Handrail (504)
535
535
535
535
535
535
Upright
528
560a
559b
537529 530
531
537
564
504 559b
Stabilizer
Leveling
Foot
Part #23-AS-566 US-English v1.0 05-Mar-17
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

assault-airrunner

Suche zurücksetzen

  • wie lese ich dieses Gerät aus. also wo sehe ich wie viele Betriebsstunden dieses gerät gelaufen ist ? Eingereicht am 3-8-2021 15:37

    Antworten Frage melden

  • Zeit im Display bleibt nach 5 Sekunden stehen (Elapsed), andere Funktionen werden nicht angezeigt, Reset hilft nicht. Ideen? Eingereicht am 20-7-2020 09:22

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Assault AirRunner wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Assault AirRunner

Assault AirRunner Bedienungsanleitung - Englisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info