Bedienungsanleitung ATAG Blauwe Engel (Seite 16 von 37) (Englisch)

507731

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

Installation instructions S-HR series page 16

9 Boiler controls

The boiler is provided with a fully automatic micropro-

cessor control. This control simplifies operation by

undertaking all major control functions. Initially when

power to the unit is switched on it will remain on standby.

The control panel display will show the relevant state.

The various parameters can be called up in two ways:

The state.

In this state the display will show during all

normal operating functions of the appliance. Should a

fault develop this will be shown on the display.

The technical read out.

Start from the state by pressing the Step key for

5 seconds. Returning from this to the display is

done in the same way. From the technical read out a more

extensive read out can be obtained e.g. the boiler flow

temperature and the water pressure in the central heating

system.

When the system has been filled and the automatic venting

program starts, when a program has been selected, the

program takes 15 minutes and stops automatically. After

this the unit will function normally.

On a call for heating or hot water the control system will

select the required water control temperature. This water

temperature is called the T-set value. On a call for central

heating the boiler ignites first at low input. The input is

then changed slowly to match the load required. The

boiler operates in this way to avoid excessive water

noises and temperature overshoot. On a call for hot water

supply the T-set value of central heating return water

temperature is monitored. Depending on the amount of

sanitary water which is withdrawn from the DHW cylinder,

the central heating return water temperature, from which

the input is adjusted, will vary.

9.1 Explanation of the function keys

Key functions from the and the extensive

indication are:

- Central Heating program key, see chapter

10.1;

- Hot Water program key, see chapter 10.2;

- PC program key, adjusts the pump to continuous

water circulation in the central heating system, or

according to the pump overrun times on the relevant

programs;

- Step key, after briefly pressing, the water pressure

can be retrieved and pages per chapter can be

retrieved. After pressing for 5 seconds it switches

from indication to technical indication and the

other way round;

- Mode key, after briefly pressing, a selection of the

data chapters can be retrieved. After pressing for 5

seconds it is possible to enter the code as described

in chapter 10.3;

- Reset key, after briefly pressing, for:

unlocking errors;

ending the access code;

ending the automatic venting program, only when

the access code is entered and the reset key is

pressed briefly.

After pressing for 5 seconds an operating stop is

made, for example, for activating the automatic

venting program.

Other key functions from the other indications are:

- Central Heating key then has the + function;

- Hot Water key then has the - function;

- PC key then has the store function, which means

that by means of this key a modified setting is

confirmed;

- Step key for scrolling in a data chapter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG Blauwe Engel Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG Blauwe Engel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info