2526
88
Zoom out
Zoom in
Vorherige Seite
1/99
Nächste Seite
TROUBLESHOOTING
table
16
Symptom
Text appears in the displays when the
appliance is first connected.
The fan runs on for several minutes
after the hob has been switched off.
A slight smell is noticeable the first
few times the hob is used.
You can hear a ticking sound in your
hob.
The pans make a noise while cooking.
You have switched a cooking zone on
but the display keeps flashing.
The hob is not working and nothing
appears in the display.
A fuse blows as soon as the hob is
switched on.
Faultcode 1E03; 1E09.
Other faultcodes.
Faultcode 1E01; 2E01; 3E01; 4E01
Faultcode 1E10
Continuous bleep.
Faultcode F11; F42.
Faultcode F99
Possible cause
This is the standard set-up routine.
The hob is cooling.
The new appliance heating up.
Ticking can also occur at lower set-
tings.
This is caused by the energy flowing
from the hob to the saucepan.
The pan you are using is not suitable
for induction cooking or has a diame-
ter of less than 12 cm.
There is no power supply due to a
defective cable or a faulty connection.
The hob has been wrongly connected..
The hob has been wrongly connected
or the mains voltage is too low.
Defective generator.
The hob has overheated.
The hob has been wrongly connected
or the mains voltage is too high.
The hob has been wrongly connected
or the main voltage is too high.
A control has been held for too long.
You pressed two buttons at once.
Solution
Normal operation.
Normal operation.
This is normal and will disappear once
it has been used a few times. Ventilate
the kitchen.
Normal operation.
At high settings this is perfectly nor-
mal for some pans. It will not damage
either the pans or the hob.
Use a suitable pan, see page 12.
Check the fuses or the electric switch
(if there is no plug).
Check the electrical connections.
Check the connection. Contact your
electricity supplier if the problem con-
tinues
Contact the service department.
The hob has been switched off due to
overheating. Let the hob cool down
and then use a lower setting.
Have the connection changed.
Contact the service department.
Have the connection changed.
Do not hold the control knobs full left
or full right for to long. If the fault-
code is still displayed, contact the ser-
vice department.
Press 1 button at a time.
88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ATAG Hi4071M wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von ATAG Hi4071M

ATAG Hi4071M Bedienungsanleitung - Holländisch - 100 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info