Bedienungsanleitung ATAG VA 6311 AF (Seite 19 von 24) (Englisch)

75793

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

When the appliance is correctly levelled, the

door will not catch on either side of the cabi-

net .

If the door does not close correctly, loosen

or tighten the adjustable feet until the ma-

chine is perfectly level.

Water connection

Water inlet connection

This dishwasher may be fed with either hot

(max. 60°) or cold water. Nevertheless we

advise you use a cold water supply.

A hot water supply is not always efficient with

heavily soiled crockery as it shortens the

washing programmes a lot.

For making the connection itself, the cou-

pling nut fitted to the machine’s inlet hose is

designed to screw onto a 3/4" gas thread

spout or to a purpose made quick-coupling

tap such as the Press-block.

The water pressure must be within the limits

given in the "Technical data". Your local Wa-

ter Authority will advise you on the average

mains pressure in your area.

The water inlet hose must not be kinked,

crushed, or entangled when it is being con-

nected.

The dishwasher features inlet and drain ho-

ses which can be turned either to the left or

the right to suit the installation by means of

the locknut. The locknut must be

correctly fitted to avoid water leaks.

Attention! NOT all models of dishwash-

ers have inlet and drain hoses provided

with a locknut. In this case, this facility is

not available.

If the machine is connected to new pipes or

pipes which have not been used for a long

time, you should run the water for a few mi-

nutes before connecting the inlet hose.

DO NOT use connection hoses which

have previously been used on an old ap-

pliance.

This appliance has been fitted with

safety features which will prevent the

water used in the appliance from return-

ing back into the drinking water system.

This appliance complies with the appli-

cable plumbing regulations.

Water inlet hose with safety valve

After connecting the double-walled water in-

let hose, the safety valve is next to the tap.

Therefore the water inlet hose is only under

pressure while the water is running. If the wa-

ter inlet hose starts to leak during this opera-

tion, the safety valve cuts off the running

water.

Please take care when installing the water

inlet hose:

• The electrical cable for the safety valve is

in the double-walled water inlet hose. Do

not immerse the water inlet hose or the

safety valve in water.

• If water inlet hose or the safety valve is

damaged, remove the mains plug

immediately.

• A water inlet hose with safety valve must

only be replaced by the Service Force

Centre.

Warning! Dangerous voltage

Water drain connection

The end of the drain hose can be connected

in the following ways:

1. To the sink outlet spigot, securing it to the

underside of the work surface. This will

prevent waste water from the sink run-

ning into the machine.

2. To a stand pipe provided with venthole,

minimum internal diameter 4 cm.

The waste connection must be at a maxi-

mum height of 60 cm from the bottom of the

dishwasher.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG VA 6311 AF Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG VA 6311 AF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info