Bedienungsanleitung ATAG VA7015NT (Seite 5 von 24) (Englisch)

692635

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Set water hardness 0/1/2/3/4/5/6/7/8/93

Adjusting the water softener. Select a setting depending on the

hardness of the water supply. It is important that this setting is correct!

Do not forget to put salt in the salt compartment after you have set

the water softener to 1 - 9.

For a water supply with a hardness under 6°dH (9°fH), select 0. The

water softener is deactivated and no salt is needed.

Pre-selected at factory: 4

Top up salt

Salt compartment lid

1 Unscrew the salt compartment lid.

2 Place the funnel supplied with the dishwasher in the salt

compartment top-up hole. First, pour in about 1 l of water.

3 Then add salt, a maximum of 1.0 kg, until the compartment is full.

4 Wipe up any excess salt so that the lid can be screwed on firmly.

In order to avoid rust stains a dishwashing programme must be started

immediately after adding salt.

To change the selected setting, see the chapter Settings.

Loading the dishwasher

Greener dishwashing

Do not rinse under running water

Simply scrape off large food particles before loading the dishwasher.

Choose a green detergent

Read the environmental declaration on the packaging!

Run programmes only with a full load

Wait to run a programme until the dishwasher is full, this way you save

energy. Use the Rinse & hold programme to rinse the dishes if there

are any unpleasant odours while you wait for the dishwasher to become

fully loaded.

Run programmes at a lower temperature

If the dishes are only slightly dirty, you can select a programme with

a low temperature.

Select Eco

This programme is intended for cleaning normally dirty dishes and is

the most effective programme in terms of combined energy and water

consumption.

The dishwashing programme is designed for an effective wash using

as little energy and water as possible. The programme washes at a

low temperature for a long time.

Open the door a little once the programme has finished

A shorter dishwashing programme and better drying results are

achieved if you use the Auto Open option, which automatically opens

the dishwasher door. Wait until the dishwasher indicates that the

programme has ended and the dishes have cooled before unloading

the dishwasher.

Connect to cold water

Connect the dishwasher to the cold water supply if the building is

heated using oil, electricity or gas.

Connection to hot water supply

Connect the dishwasher to the hot water supply (max. 70 °C) if the

building is heated using an energy-efficient means such as district

heating, solar power or geothermal power. Choosing a hot water

connection cuts dishwashing times and reduces the dishwasher's

energy consumption.

NOTE!

Do not exceed the permitted water supply temperature. Certain

materials used in some cookware cannot withstand strong heat.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG VA7015NT Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG VA7015NT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info