Bedienungsanleitung ATAG VA7015QT (Seite 14 von 24) (Englisch)

675542

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Care and cleaning

Coarse filter

The coarse filter traps larger food particles, which cannot get past the

drainage pump. Empty the coarse filter as necessary.

Coarse filter

1 Lift the coarse filter by the handle.

2 Empty the coarse filter. Remember to replace it!

Fine filter

Debris that collects on the fine filter is automatically rinsed away during

each wash. Clean the fine filter when necessary.

Fine filter

1 Turn the handle anticlockwise.

2 Lift the filter straight up using the handle. Free the coarse filter to

clean the fine filter.

3 Replace in reverse order. Check that the edges seal properly when

replacing the fine filter.

4 Lock the filter in place by turning the handle clockwise to the stop

position. The handle should point straight out from the dishwasher.

NOTE!

The dishwasher must not be used without the filters in place!

Dishwashing results may be affected if the coarse filter is incorrectly

fitted.

Spray arms

Holes and bearings can sometimes become blocked. Remove any

debris using a pin or the like. The spray arms also have holes

underneath.

To facilitate cleaning you can remove the spray arms. Remember to

fit them firmly back into place afterwards.

Upper spray arm

1 Pull out the upper basket.

2 Unscrew the spray arm bearings counterclockwise to remove the

spray arm from the upper basket.

Lower spray arm

• Pull the lower spray arm straight up to release it.

The door and the door seal

Regularly clean the sides of the door and the door seal. Use a slightly

damp cloth (with a little cleaner if necessary).

Front panel

Keep the buttons clean and free from grease. Wipe them clean with a

dry or slightly damp cloth. Never use cleaners – they can scratch the

surface. Use the main power switch to turn off the dishwasher before

cleaning the buttons to avoid activating any buttons unintentionally.

The dishwasher tub

The dishwasher tub is made of stainless steel and is kept clean through

normal use.

Limescale deposits

If you have hard water, limescale deposits may build up in the

dishwasher. If this happens, run the Self-cleaning programme with two

tablespoons of citric acid in the detergent compartment (with no dishes

in the machine). Special dishwasher cleaners are also available on the

market.

Unblocking the drainage pump

If the dishwasher still contains water after the programme has finished,

something may be blocking the drainage pump. Such items are easily

removed.

1 Turn off the machine using the main power switch and unplug it

from the wall socket.

2 Remove the coarse filter and the fine filter.

3 Scoop out the water from the dishwasher tub.

4 In order to inspect the drainage pump, remove the coloured stop

on the right in the bottom drain.

5 Turn the pump wheel located behind the drainage pump stop by

hand. Carefully remove any items.

6 Replace the drainage pump stop along with the fine and coarse

filters.

7 Plug the machine in again.

If the dishwasher still does not start and a whirring sound is heard,

the overflow protection has been activated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG VA7015QT Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG VA7015QT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info