Bedienungsanleitung ATAG WN2..K (Seite 7 von 28) (Holländisch)

2594

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Introduction to the Hood - Fig. 1.1

1. Light Switch

2. Motor Speed Switch

3. Illumination of the cooking surface

4. Grease Filters/grease filter support grate

5. Light Cover Supports

6. Pull-Out Drawer

Model with Grease Filter Support Grate

Opening the Grease Filter Support Grates - Fig. 2.1

a. Remove the pull-out drawer completely.

b. Push the A knobs inwards toward each other (in the

“Open” direction as indicated on the plastic knob itself).

c. To remove the grates completely, use the B spring

fasteners, which act as pins to hold the grate in place

(Fig. 3).

Model with Self-supporting Metal Filters

Removing the Grease Filters - Fig. 2.2

a. Remove the pull-out drawer completely.

b. Press the side handles C (some models are supplied

with handles Z - Fig. 2.3) towards the opposite side

and remove the filters.

Putting the Filters Back in Place

a. Remove the pull-out drawer completely and mount the

grease filter so that it covers the drawer.

b. Close the drawer and install the remaining grease filter.

Opening the Light Cover Support

a. Remove the pull-out drawer completely.

b. According to model in possession:

Lamp D with hook locks type A - Fig.2.2

Move the bracket hook locks towards each other (in

direction “Open” as printed on the plastic part of the

lock). Lamp F with hook locks type G - Fig. 1.2

Move the hook locks as indicated by the arrows and

completely remove the lamp from the housing (Fig.

1.3).

Systems Available

Venting Outdoors

The air is vented outdoors through a duct which must be

connected to the exhaust opening K (Fig. 5) by means of

the flange H. The diameter of the exhaust duct must be

exactly the same as that of the flange.

Air Recirculation

— The air is cleaned by means of charcoal filters and then

circulated back into the room.

— The use of a charcoal filter is necessary when the hood

cannot vented outdoors either because ducting is not

available or cannot be installed.

— The filtered air is returned from atop the cabinet through

a duct that passes through the cabinet itself.The

diameter of the duct must be the same as that of flange

H (Fig. 5).

The deflector J can be fixed to the outlet hole using the

two screws provided

(Fig. 4).

To fit or replace a carbon filter:

a. Request a charcoal filter from the retailer, specifying

the model and type of hood.

Caution! Some charcoal filters come covered with a

plastic film to protect their filtering properties. If this is the

case, remove the film before installing the filter.

b. Remove the pull-out drawer completely.

c. Remove the grease filters or the grates.

d. Place the activated carbon filter in position:

1) Version with one motor: insert the filter in its housing

over the plastic grill and rotate it until it locks in

position (Fig. 6).

2) Version with two motors: to assemble the filter,

insert it in its seating and fix it in position using the

clips L (Fig. 7)

e. Remove the grease filters or grills

To remove the carbon filter, follow the procedure

described in item 1) or 2), depending on the version) in

the reverse order.

Installation

When installed, the distance between the hood and burners

must be not less than 43 cm for electric burners or 65 cm

for gas or mixed-fuel burners.

Caution

This appliance is designed to be operated by adults.

Children should not be allowed to tamper with the controls

or play with the appliance.

Do not use the cooker hood where the grill is not correctly

fixed! The suctioned air must not be conveyed in the same

channel used for fumes discharged by appliances powered

by other than electricity. The environment must always

be adequately aerated when the cooker hood and other

appliances powered by other than electricity are used at

the same time. Flambé cooking with a cooker hood is

prohibited. The use of a free flame is damaging to the filters

and may cause fire accidents, therefore free flame cooking

must be avoided. Frying of foods must be kept under close

control in order to avoid overheated oil catching fire. Carry

out fumes discharging in accordance with the regulations

in force by local laws for safety and technical restrictions.

The manufacturers refuse to accept any responsibility for

damage to the hood or its catching on fire because of failure

to observe the above instructions.

Electrical connection

The electrical tension must correspond to the tension noted

on the label placed inside the cooker hood. Connect the

electrical plug, where provided, to the an easily accessible

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG WN2..K Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info