Bedienungsanleitung ATAG WS 1011 LM (Seite 10 von 12) (Deutsch, Englisch, Holländisch, Französisch)

108404

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

- 10 -

GENERAL

Carefully read the following important information regarding

installation safety and maintenance. Keep this information

booklet accessible for further consultations.

The appliance has been designed for use in the ducting

version (air exhaust to the outside – Fig.1B), filtering

version (air circulation on the inside – Fig.1A).

SAFETY PRECAUTION

1. Take care when the cooker hood is operating

simultaneously with an open fireplace or burner that

depend on the air in the environment and are supplied by

other than electrical energy, as the cooker hood removes

the air from the environment which a burner or fireplace

need for combustion. The negative pressure in the

environment must not exceed 4Pa (4x10-5 bar). Provide

adequate ventilation in the environment for a safe

operation of the cooker hood.

Follow the local laws applicable for external air evacuation.

2. WARNING !

In certain circumstances electrical appliances may be

a danger hazard.

A) Do not check the status of the filters while the

cooker hood is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker

hood

D) Avoid free flame, as it is damaging for the filters

and a fire hazard

E) Constantly check food frying to avoid that the

overheated oil may become a fire hazard

F) Disconnect the electrical plug prior to any

maintenance.

G) This appliance is not intended for use by young

children or infirm persons without supervision

H) Young children should be supervised to ensure they

do not play with the appliance

I) There shall be adequate ventilation of the room

when the rangehood is used at the same time as

appliances burning gas or other fuels

L) There is a risk of fire if cleaning is not carried out

in accordance with the instructions

INSTALLATION INSTRUCTIONS

• Electric Connection

The appliance has been manufactured as a class II,

therefore no earth cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load

indicated on the description label. Where a plug is

provided, the cooker hood must be installed in order that

the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm

between contacts, in line with the electrical load and

local standards, must be placed between the appliance

and the network in the case of direct connection to the

electrical network.

• The appliance must be installed at a minimum height of

700 mm from an cooker stove in case of a gashob or an

electrical hob.

If a connection tube composed of two parts is used, the

upper part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same

conductor used to circulate hot air or for evacuating

fumes from other appliances generated by other than an

electrical source.

Before proceeding with the assembly operations, remove

the anti-grease filter(s) (Fig.6) so that the unit is easier

to handle.

• FIXING TO THE WALL

Drill the holes A respecting the distances indicated (Fig.2).

Fix the appliance to the wall and align it in horizontal

position to the wall units. When the appliance has been

adjusted, definitely fix the hood using the screws A (Fig.4).

For the various installations use screws and screw an-

chors suited to the type of wall (e.g. reinforced concrete,

plasterboard, etc.). If the screws and screw anchors are

provided with the product, check that they are suitable for

the type of wall on which the hood is to be fixed.

• FIXING THE DECORATIVE TELESCOPIC FLUE

Arrange the electrical power supply within the dimensions

of the decorative flue. If your appliance is to be installed in

the ducting version, prepare the air exhaust opening.

Adjust the width of the support bracket of the upper flue

(Fig.3). Then fix it to the ceiling using the screws A (Fig.3)

in such a way that it is in line with your hood and respect-

ing the distance from the ceiling indicated in Fig.2. Con-

nect the flange C to the air exhaust hole using a connec-

tion pipe (Fig.4).

Insert the upper flue into the lower flue. Fix the lower flue

to the hood using the screws B provided (Fig.4), extract

the upper flue up to the bracket and fix it with the screws

B (Fig.3). To transform the hood from a ducting version into

a filtering version, ask your dealer for the charcoal filters

and follow the installation instructions.

• FILTERING VERSION

Install the hood and the two flues as described in the

paragraph for installation of the hood in ducting version. To

assemble the filtering flue refer to the instructions con-

tained in the kit. If the kit is not provided, order it from your

dealer as accessory. The charcoal filters must be fitted in

the ducting unit located inside the hood (Fig.7).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to

cooking.

It is recommended to leave the appliance in operation for

15 minutes after cooking is terminated in order to

completely eliminate cooking vapours and odours.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG WS 1011 LM Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info