Bedienungsanleitung ATAG WU 9011 GC (Seite 11 von 13) (Deutsch, Englisch, Holländisch, Französisch)

121861

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

GENERAL

Carefully read the following important information regarding

installation safety and maintenance. Keep this information

booklet accessible for further consultations. The appliance has

been designed for use in the ducting version (air exhaust to

the outside – Fig.1B),  ltering version (air circulation on the

inside – Fig.1A) or with external motor (Fig.1C).

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously

with an open  replace or burner that depend on the air in the

environment and are supplied by other than electrical energy,

as the cooker hood removes the air from the environment

which a burner or  replace need for combustion. The negative

pressure in the environment must not exceed 4Pa (4x10-5 bar).

Provide adequate ventilation in the environment for a safe

operation of the cooker hood. Follow the local laws applicable

for external air evacuation.

Before connecting the model to the electricity network:

- Control the data plate (positioned inside the appliance)

to ascertain that the voltage and power correspond to the

network and the socket is suitable. If in doubt ask a quali ed

electrician.

2. Warning !

In certain circumstances electrical appliances may be a

danger hazard.

A) Do not check the status of the  lters while the cooker

hood is operating

B) Do not touch bulbs or adjacent areas, during or straight

after prolonged use of the lighting installation.

C) Disconnect the electrical plug prior to any

maintenance.

D) This appliance is not intended for use by young children

or in rm persons without supervision

E) Young children should be supervised to ensure they do

not play with the appliance

F) There shall be adequate ventilation of the room when

the rangehood is used at the same time as appliances

burning gas or other fuels

G) There is a risk of  re if cleaning is not carried out in

accordance with the instructions

This appliance conforms to the European Directive, Waste

Electrical and Electronic Equipment (WEEE). By making sure

that this appliance is disposed of in a suitable manner, the user

is helping to prevent potential damage to the environment

or to public health.

The

symbol on the product or on the accompanying

paperwork indicates that the appliance should not be treated

as domestic waste, but should be delivered to a suitable

electric and electronic appliance recycling collection point.

Follow local guidelines when disposing of waste. For more

information on the treatment, re-use and recycling of this

product, please contact your local authority, domestic waste

collection service or the shop where the appliance was

purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out

by specialised personnel.

• Electric Connection

The appliance has been manufactured as a class II, therefore

no earth cable is necessary.

The plug must be easily accessible after the installation of

the appliance.

• If the hob is electric, gas, or induction, the minimum distance

between the same and the lower part of the hood must be

at least 65 cm.

If a connection tube composed of two parts is used, the

upper part must be placed outside the lower part. Do not

connect the cooker hood exhaust to the same conductor

used to circulate hot air or for evacuating fumes from other

appliances generated by other than an electrical source.

Before proceeding with the assembly operations, remove

the anti-grease  lter(s) (Fig.2) so that the unit is easier to

handle.

- In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

• We recommend the use of an air exhaust tube which has

the same diameter as the air exhaust outlet hole. If a pipe

with a smaller diameter is used, the e ciency of the product

may be reduced and its operation may become noisier.

• Installation

The following instruction should be followed to carry out the

correct installation of the cooker hood.

1. Mounting of the cooker hood on the lower side of the

cupboard.

2. Selection of the version (extraction or  ltration)

3. Before starting to  x the hood, disconnect the anti-grease

 lter for easier appliance handling:

- Open panel B as shown in Fig.2.

- Pull handle C as shown in Fig.3.

• Fitting the cooker hood into the lower part of the wall

cabinet

For all measurements relating to the cooker hood, please

refer to Fig.4.

Before  xing the cooker hood to the lower part of the cabinet,

the following steps should be performed:

1- Remove the 4 screws E  xing the two cooker hood lamps H

(RHS and LHS) in place as indicated in Fig. 5A.

2- Remove the lamps H and disconnect the connectors W of

the halogen lamps to make installation easier, as indicated

in Fig. 5B.

3. Make sure the thickness of the cabinet falls within the range

of values listed in Fig. 5C.

Fit the cooker hood in the cabinet (Fig. 6) and make sure the

4 springs are  xed in place well.

Fix the cooker hood to the cabinet securely by using a

screwdriver to tighten the screws M until the appliance is

 ush with the cabinet (Fig. 6).

4. Connect the connectors W of the halogen lamps again and

reinstall the lamps H  xing them with the 4 screws E that were

previously removed.

ENGLISH

- 12 -

ATAG WU 9011 GC Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info