Bedienungsanleitung ATAG WV 9211 LM (Seite 15 von 16) (Deutsch, Englisch, Holländisch, Französisch)

110102

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

2. Fix it in place using 4 screws B which are suited to the type

of cabinet installed, as indicated in  gure 4.

- Fixing the hood to the wall (Fig. 5B)

1. Using the drill template supplied, make 2  xing holes in

accordance with the measurements listed.

When carrying out the  xing procedures, use only screws

and screw anchors which are suited to the type of wall (e.g.

reinforced concrete, plasterboard etc.). If the screws and

screw anchors are supplied with the appliance, make sure

that they are suited to the type of wall to which the hood

must be  xed.

Adjust the position of the brackets M in accordance with

the cabinet depth, using the caged nut N as indicated in

 gure 5A.

2. Fix the hood to the bracket using screw G as indicated

in  gure 5B.

3. Fix the hood to the wall using the 2 screws R (Fig. 5C).

- Fitting the spacers

Depending on your appliance model, use the following

installation instructions:

1. spacer I (Fig. 6).

To  ll in any space remaining between the hood and the wall,

simply position spacer I next to the wall and  x it in place

with the 3 screws

L as indicated in  gure 6.

2. spacer O (Fig. 7).

see note (*) Warning: plastic spacer  tting

• Extractor version

When installed in this way the appliance expels fumes outside,

either through a perimeter wall or existing ducting. It is

therefore necessary to purchase a non- ammable air exhaust

tube which complies with all current legislation and connect

it to the  ange F supplied (Fig. 8).

• Filter version

To transform an extractor hood version into a  lter hood

version, contact your appliance dealer and ask for active

carbon  lters.

The air is released back into the room through connection

piping which passes through the cabinet and is connected

to  ange F (Fig. 9).

The active carbon  lters must be  tted inside the hood.

To replace the filters, pull lever H outwards as shown in

(Fig.3).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked.

We also recommend that the appliance is left running for

15 minutes after the food is cooked, in order to thoroughly

eliminate all contaminated air.

The e ective performance of the cooker hood depends on

constant maintenance; the anti-grease  lter and the active

carbon  lter both require special attention.

• The anti-grease  lter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the  lter to become saturated depends on

the way in which the appliance is used).

- To prevent potential  re hazards, the anti-grease  lters should

be washed a minimum of every 2 months (it is possible to use

the dishwasher for this task).

- After a few washes, the colour of the  lters may change. This

does not mean they have to be replaced.

If the replacement and washing instructions are not followed,

the anti-grease  lters may present a  re hazard.

• The active carbon  lters are used to purify the air which is

released back into the room.

The  lters are not washable or re-usable and must be replaced

at least once every four months.

The active carbon  lter saturation level depends on the fre-

quency with which the appliance is used, the type of cooking

performed and the regularity with which the anti-grease

 lters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with denatured

alcohol or neutral, non-abrasive liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination.

Extended use of the light reduces the average duration of

the bulb.

• Commands: (Fig.11)

Push-button A = on/o lights switch

Push-button B = on/o cooker hood switch. The appliance

switches on at speed level 1, If the cooker hood is on depress

the push-button for 2 sec. to switch o the cooker hood. If

the cooker hood is at speed level 1 it will not be necessary

to depress the push-button to switch the cooker hood o .

Decreases the motor speed.

Display C = indicates the motor speed level selected and

activates the timer.

Push-button D = switches on the cooker hood. Increases the

motor speed. Touching the key at 3rd speed, the intensive

function runs for 10’, then the appliance go back to work at the

original speed. During this function the display blinks.

Key E = The Timer times the functions on activation for 15

minutes, after which they are switched o . The Timer is deac-

tivated by re-pressing Key E. When the Timer is activated the

decimal point must  ash on the display. The Timer cannot be

activated if the intensive speed is functioning.

The “clean air” function is activated by pressing key E for 2

seconds when the appliance is switched o . This switches the

motor on for 10 minutes every hour at the  rst speed. During

functioning a rotary movement of the peripheral segments

must be visualised on the display. When this time has passed

the motor switches o and the  xed letter “C” must be visu-

alised on the display until the motor re-starts after 50 minutes

for another 10 minutes and so on. Press any key apart from

the light keys to return to normal functioning. Press key E to

deactivate the function.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

ABOVE WARNINGS.

- 15 -

ATAG WV 9211 LM Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info