Bedienungsanleitung Atika Bioline 1600 (Seite 21 von 39) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

519866

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

2. Safety Instructions

Machine including safety cut-out

The safety cut-out, including an automatic motor

brake, which is attached to the shredder is used

for the safety of the machine, preventing the

motor being started when the machine is open

and the rotating knives could be reached by the

operator’s hand.

Repairs on electrical parts of the machine and

on the safety cut-out must be done by the

producer or by a company designated by the

producer.

Please read the following

safety instructions carefully.

• Within his area of work the operator is

responsible for third parties.

• The machine must not be used by opera-

tors under the age of 16.

• Keep children away form machine.

• Wear protective goggles, gloves and noise

protection while working with the machine.

• The connecting lead to IEC 60245

(H 07 RN-F) should be equipped with a

rubber plug. The lead section should be

a minimum of 3 x 1,5 mm².

• Never use faulty connecting leads.

• Connect the machine using a residual

current petector.

• Always switch off motor before main-

tenance and cleaning of shredder.

Remove mains plug from socket (also

during transport and when leaving

machine unattended).

• Do not operate without the funnel.

• Close machine properly before enabling

motor.

• Faulty or damaged parts in the device

must be replaced immediately.

• Never reach into the filling or ejection

opening when the machine is running.

• Do not spray machine with water (this

is hazardous due to live components).

• Wear safety gloves during assembly

and cleaning work.

• Never modify the machine or parts thereof.

• Only use the machine for the purposes

listed under Section 4 "Shredding".

• Do not leave the machine standing in

the rain or use when raining. Store the

machine in a dry place.

• To prevent danger of injury to fingers during

assembly or cleaning operations hold the cut-

ting mechanism (for example by means of a

wooden wedge, see. pic. p. 21) and wear

protecting gloves.

3. Start-up

• Check that the machine is completely and

correctly assembled.

• To avoid toppling, place the chopper on a firm

horizontal surface.

• Connect the machine to an appropriate and

correctly wired electric socket.

• Only use extension leads with sufficient dia-

meters:

- cable up to 25 metres: diameter at least

1,5 mm².

- cable over 25 metres: diameter at least

2,5 mm².

• Fuse protection:

- 1100 W, 1200 W: 10 A

- 1300 W, 1400 W, 1500 W,

1600 W, 1700 W: 10 A inert

- 1800 W, 1900 W, 2000 W: 16 A

- 2100 W, 2200 W, 2300 W

2400 W: 16 A inert

- for UK use 13 A fuse (all models)

• Before using the shredder, make sure each

time that

- there are no faulty connections (tears, cuts,

etc.)

- all screws are tight.

Important:

Before using the shredder for the first time,

close top of case and screw tight.

Switch on and off

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika Bioline 1600 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info