Bedienungsanleitung Atika BMS250 (Seite 21 von 101) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Polnisch, Schwedisch)

519289

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

parts must be correctly installed and fulfil all conditions

to ensure perfect operation of the saw

− Damaged guards and parts must be properly repaired

or exchanged by a recognized, specialist workshop;

insofar as nothing else is stated in the instructions for

use.

− Damaged or illegible security labels have to be

replaced.

 Do not allow any tool key to be plugged in!

Before switching on, check always that wrenches and

adjusting tools are removed.

 Store unused equipment in a dry, locked place out of the

reach of children.

Electrical safety

 Design of the connection cable according to IEC 60 245 (H

07 RN-F) with a core cross-profile section of at least

− 1.5 mm2 for cable lengths up to 25m

− 2.5 mm2 for cable lengths over 25m

 Long and thin connection lines result in a potential drop.

The motor does not reach any longer its maximal power; the

function of the device is reduced.

 Plugs and coupler outlets on connection cables must be

made of rubber, non-rigid PVC or other thermoplastic

material of same mechanical stability or be covered with this

material.

 Protect yourself against electric shocks. Avoid touching

earthed parts with your body.

 The connector of the connection cable must be splash-

proof.

 Wind off completely the cable when using a cable drum.

 Do not use the cable for purposes for which it is not meant.

Protect the cable against heat, oil and sharp edges. Do

not use the cable to pull the plug from the socket.

 Regularly check the saw cable and if damaged, have it

renewed by a recognised skilled electrician.

 When running the connection line observe that it does not

interfere, is not squeezed, bended and the plug connection

does not get wet.

 Regularly check the extension cables and replace them if

they are damaged.

 Do not use any defective connection cables.

 When working outdoors, only use extension cables

especially approved and appropriately labelled for outdoor

use.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 Only hook up the machine by means of a fault-current

circuit breaker (30 mA).

The electrical connection or repairs to electrical parts of

the machine must be carried out by a certified electrician

or one of our customer service points. Local regulations –

especially regarding protective measures – must be

observed.

Repairs to other parts of the machine must be carried out

by the manufacturer or one of his customer service

points.

Use only original spare parts and accessorie parts.

Accidents can arise for the user through the use of other

spare parts. The manufacturer is not liable for any damage

or injury resulting from such action.

Assembly of the saw

A1 A2 A33

Unfold the stand (16).

1. Bring the frame stand together so that the lock is released.

2. Pull up the frame until it latches again.

B1 B2

Install the transport wheels (18).

Turn the saw around. You can align the saw by turning the

adjusting foot (17) in or out.

Install splitting wedge

1. Turn the screw out.

2. Place the screwdriver in the hole to take out the table insert

(6).

Raise the saw blade (22) to its highest position.

Loosen the screw on the clamp.

Insert the splitting wedge (23) between the pressure plate (33)

and the counter-plate (34).

1. Adjust the splitting wedge (23). The distance between the

saw blade and splitting wedge must be max. 5 mm.

2. Retighten the screw on the clamp.

1. Reinsert the table insert (6).

2. Stand behind the saw, insert the screwdriver in the hole and

pull it towards you so that the table insert latches in place.

3. Retighten the screw for attaching the table insert.

Attach the safety guard (5) using an M6 x 40 coach bolt and an

M6 wing nut on the splitting wedge (23).

F1 F2

Screw both holders (27 and 28) on.

Install bench length extension

Attach the bench length extension (1) using the two hex head

screws M6 x 12.

G2 G3

Attach the supports (24) to the bench length extension (1) using

two hex head screws M6 x 12, washers A 6,4 and M6 hex nuts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BMS250 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info