Bedienungsanleitung Atika BS 205-2 (Seite 17 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch)

701023

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

 Persons under the age of 18 must not operate the band

saw. An exception is youngsters under the age of 16 within

the scope of their vocational training under supervision.

 Keep other persons away.

Do not allow other persons, especially children, to touch the

tool or cable.

Keep them away from your working area.

 Take the correct working position. The saw teeth must show

to the operator.

 Only begin cutting after the saw band has reached its

required rotational speed.

 Do not force the power tool. You work better and safer in

the given performance range.

 Only operate the machine with complete and correctly

attached safety equipment and do not alter anything on the

machine that could impair the safety.

 Do not use any cracked saw bands or such that have

changed their shape.

 Use only sharp saw bands since dull saw bands not only

increase the danger of back kicking but also cause

excessive load on the motor.

 Do use only saw bands according to ISO 3295 / DIN 8806-

The use of other tools and other accessories may

present a risk of injury to you.

 Do not use the saw for purposes it is not intended for (see

proper use).

 When longitudinally cutting narrow workpieces (distance

between the saw blade and the parallel rip fence less than

120 mm), use the pushstick. (see “working instructions”).

 To push narrow workpieces against the parallel rip fence,

use a push block.

 Push blocks can be purchased in retail outlets.

 Do not use defective pushsticks and blocks.

 See to it that the pieces cut off are not caught and thrown

away by the saw band.

 Do not remove the splints, splinters and wastes with the

hand out of the danger zone of the saw band.

 Cutting round timber is not allowed with the standard

feeding assistances. When cutting round timber use a

special device which safes the work piece from skewing.

 Switch the machine off and remove the mains plug from the

socket when

 carrying out repair works

 maintenance and cleaning

 carrying out servicing and repair works, removal of faults

(this also includes removing clamped splinters)

 checks of connecting lines, whether these are knotted or

damaged

 transporting the saw

 saw band exchange

 leaving the saw unattended (even during short

interruptions)

 Maintain your machine with care:

 Keep your tools sharp and clean in order to be able to

work better and safer.

 Follow the maintenance instructions and the instructions

for tool exchange.

 Keep the handles dry and free of oil and grease.

 Check the machine for possible damage:

 Before further use of the machine the safety devices and

any parts that show minor damages must be checked

carefully for their proper and intended function.

 Check whether movable parts function perfectly and do

not stick or whether parts are damaged. All parts must

be correctly installed and fulfil all conditions to ensure

perfect operation of the machine.

 Damaged safety devices and parts must be properly

repaired or exchanged by a recognized, specialist

workshop; insofar as nothing else is stated in the

instructions for use.

 Damaged or illegible safety labels have to be replaced.

 Do not allow any tool key to be plugged in!

Before switching on, check always that wrenches and

justing tools are removed.

 Store unused equipment in a dry, locked place out of the

reach of children.

Electrical safety

 Design of the connection cable according to IEC 60245 (H

07 RN-F) with a core cross-section of at least

 1.5 mm² for cable lengths up to 25 m

 2.5 mm² for cable lengths over 25 m

 Long and thin connection lines result in a voltage drop. The

motor does not reach any longer its maximal power; the

function of the device is reduced.

 Protect yourself against electric shocks. Avoid body contact

with grounded parts (e.g. pipes, heating apparatus, cookers,

fridges etc.).

 Do not use the cable for purposes for which it is not meant.

Protect the cable against heat, oil and sharp edges. Do not

use the cable to pull the plug from the socket.

 Check regularly the cable of the saw and get possible

damages repaired by an accepted specialist.

 When running the connection line observe that it does not

interfere, is not squeezed, bended and the plug connection

does not get wet.

 Regularly check the extension cables and replace them if

they are damaged.

 Do not use any defective connection cables.

 When working outdoors, only use extension cables

especially approved and appropriately labelled for outdoor

use.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 Only hook up the machine by means of a fault-current circuit

breaker (30 mA).

The electrical connection or repairs to electrical parts of

the machine must be carried out by a certified electrician

or one of our customer service points. Local regulations –

especially regarding protective measures – must be

observed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BS 205-2 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika BS 205-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info