Bedienungsanleitung Atika BS 205-2 (Seite 21 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch)

701023

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

Cutting long workpieces

Secure long workpieces against dropping down when

finishing the cutting process. Use roller supports or similar

devices for this purpose.

The sawing process

1. Select and adjust parallel stopper (8) and saw table incline

corresponding to the cutting type.

When sawing with parallel stopper and inclined

saw table the work piece can cant. The parallel stopper

must therefore be fixed on the downwards inclined side of

the saw table.

2. Adjust distance between saw band coping and work piece

to 3 mm.

3. Put work piece on the saw table.

4. Put in power plug.

5. Switch on saw.

6. Saw through work piece in one work step.

 Hint:

Make always a test cut to be able to correct the

adjustment.

7. Switch off saw when it is not intended to go on sawing.

Maintenance and cleaning

Before each maintenance and cleaning work

 switch off device

 wait for stop of saw

 pull out power plug

Further maintenance and cleaning works than described in this

chapter shall only be carried out by the manufacturer or

companies named by the manufacturer.

For maintaining and cleaning, removed security devices must

unconditionally be mounted properly and proved again.

Use only original parts. Other parts can result in unexpected

damages and injuries.

Cleaning

 Observe the following to maintain the functionality of

the saw.

 Do not wash down device with water.

 Remove splints and sawdust only with a brush or vacuum

cleaner.

 Clean and oil all moving parts regularly.

 Never use any grease!

 Use for instance sewing machine oil, liquid hydraulic

fluid or environmentally acceptable spray oil.

 Provide that the saw band stays rust-free and resin-free.

 Remove all resin residues from the saw bench top.

 Resin residues can be removed with a commercial

maintenance and care spray.

 Treat the surface of the saw table after cleaning with an

anti-blocking agent.

 The saw band is a wearing part and becomes edgeless

after longer or more frequent use respectively.

 Renew then the saw band.

Maintenance

Saw band exchange

Danger of cutting! Wear gloves when replacing the

saw band.

 Only use suitable saw bands.

Unscrew the two star knob nuts (A) and the nut (B) on

the underside of the saw table (6).

7. Pull off the stopper guidance profile (7).

Open both case doors (2 / 4).

3. Put the saw band coping (11) completely down.

4. Put upper band roll (13) down.

 turn the adjusting wheel (1) anti-clockwise, the saw band

is relaxed

5. Take out saw band.

6. Put in new saw band.

 Pay attention to a correct position: the teeth must

show forward (direction door).

7. Put saw band centrally on the band rolls (13) / (5).

8. Turn adjusting wheel (1) clockwise until the saw band does

not glide off any longer.

9. Fasten guidance gib (7) and close lower case door.

10. Subsequently:

 Clamp saw band („Saw band tension“ p. 19)

 Adjust saw band („Incline of the upper band saw roll“ p.

19)

 Adjust band guidances („upper band guidance“ and

„lower band guidance“ p. 21)

 Keep saw running at least one minute for testing

 Switch off saw, pull out power plug and recheck

adjustments

Adjusting upper band guidance

The upper band guidance consists of:

 two guide pins (these guide the saw band laterally)

 a support roller (this supports the saw band from behind)

 Check the two guide pins and the support roller after

each saw band exchange and each saw band

adjustment and readjust it if necessary.

 Guide pins and support roller are wear parts. Check

these regularly and replace the rolls in case of wear at

the same time.

To adjust the guide pins:

1. Release screws (J / K).

2. Push the guide pins (L/ M) against the saw band.

3. Open upper door and turn band saw roll several times

manually clockwise.

 Both guide rollers must abut slightly on the saw band.

4. Fasten screws (J / K).

Close upper case door.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika BS 205-2 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika BS 205-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info