Bedienungsanleitung Atika Comet 130 S (Seite 17 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

519916

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Cleaning Maintenance

The concrete mixer requires practically no maintenance.

Additional safety instructions

The mixing drum and drive shaft are bedded on ball bearings with

permanent lubrication.

Pull plug each time before cleaning.

 Never grease the ring gear!

To preserve the value of the mixer and increase its service life,

handle it as described in "Transport and storage". Furthermore,

the concrete mixer should be checked regularly for signs of wear

and tear or functional deficiencies. This applies especially to

moving parts, screw connections, protective devices and

electrical parts.

• Switch off machine and pull plug if you have to touch the

machine (with hand, brush, scraper, rag, etc.) while cleaning

it.

• Protective devices removed for cleaning must be properly

remounted before starting the machine.

• Do not spray water directly on the motor or the switch, nor on

the ventilation apertures in the motor housing.

Repair

L Notes on cleaning:

• Before taking a break and after finishing work, clean the

concrete mixer inside and out.

Pull plug each time before doing repair work.

• Do not pound on the mixing drum with hard objects

(hammer, shovel, etc.). A dented mixing drum impairs mixing

operations and is difficult to clean, besides.

• Switch off machine and pull plug if repair work should be

necessary. Do not start machine during repair work.

• To clean the inside of the drum, put in some water and a few

shovels full of gravel and set the drum to revolving.

• Protective devices removed for repairs must be properly

remounted before starting the machine.

• Remove any concrete or mortar left sticking to the teeth of

the axle-drive bevel gear or the crown gear segments

immediately.

• Only the manufacturer or companies authorised by the

manufacturer may perform repair work on electrical parts or

on parts which affect the space needed to mount electrical

equipment.

• Use only unaltered original spare parts. Otherwise, the

manufacturer will assume no liability.

• Adjust tooth play (if possible) ¨ see P. 113.

Equipment failures

Malfunction Possible cause Remedy

Motor does not start up

⇒ no mains voltage

⇒ defective cable

⇒ check fuse protection

⇒ have checked or replaced (electrician)

⇒ thermostat is triggered « reason:

− motor overload

− motor not getting enough air owing to

clogged ventilation apertures

⇒ allow motor to cool and then find and eliminate

whatever caused the thermostat to respond

Motor hums but does not start

⇒ blocked crown gear

⇒ defective condenser

⇒ switch off machine, pull plug and clean or

replace the crown gear segments

⇒ send machine to manufacturer or a company

designated by the manufacturer for repairs

Machine starts up, but

becomes blocked at low load

and may switch off auto-

matically

⇒ extension cord is too long or its cross-section

is too small

⇒ socket is too far from mains connection and

the connecting wire's cross section is too small

⇒ extension cord must be at least 1.5 mm² for a

maximum length of 25 m; the cross-section of

longer cables must be at least 2.5 mm²

Guarantee

Please observe the enclosed terms of guarantee.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika Comet 130 S Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info