519918

Atika Dynamic 165 Seite 15

15
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
• Do not reach into mixer when it is running
(
rotating mixing apparatus). Observe
enough safety distance to the concrete
mixer. Prevent any contact to rotating or moving parts of the
machine.
13
• Fill or empty the mixing drum only when the motor is running.
• Observe the mixer's direction of rotation.
• Do not alter the revolution speed of the motor, since this
controls the safe maximum operating speed, and protects the
motor and all rotating parts against damage due to excess
speed.
• Concrete mixers which the manufacturer has not intended for
towed vehicle operation may only be run by means of a hand
wire pull.
• Be absolutely sure to pull the plug before:
− moving or transport
− cleaning, maintenance or repair work
− eliminating faults
− checking connecting lines, whether these are knotted or
damaged
− leaving unattended (even during short interruptions)
• Check the machine for possible damage:
− Before further use of the machine the safety devices must
be checked carefully for their proper and intended
function.
− Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation of the machine.
− Damaged safety devices and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
− Damaged or illegible safety labels have to be replaced.
• Store unused equipment in a dry, locked place out of the
reach of children.
Shockproof concrete mixers
(Protection Class II)
• Only start the machine when the panelling is complete and
fully closed.
• Protection Class II applies only if original insulating material
is used for repairs and insulation clearances are not altered.
Electrical safety
Danger to life and limb if not observed!
• Connecting attachments must be designed in conformance
with IEC 60245-4:1980 (DIN 57 282) and marked H 07 RN-F,
or comparable models. Cross section of wires at least 3 x 1.5
mm² up to a maximum length of 25 m. Wire cross-section at
least 2.5 mm² for lengths of more than 25 m.
• Use only connecting attachments with a rubber plug device
for severe requirements that is protected against
spraying water.
•
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power;
the function of the device is reduced.
• Unwind the cable completely when using a cable drum.
• Do not use the power cords for purposes they are not
intended for. Protect the cable against heat, oil and sharp
edges. Do jerk on the power cable when pulling the plug from
the socket.
• Check connecting attachments for defects or ageing before
using them.
• Never use defective connecting attachments.
• When laying the connecting attachments, be sure that they
do get crushed or bent, and that the plug-and-socket
connection does not get wet.
• Do not use any provisional electrical connections.
• Never bridge over protective devices or put them out of
operation.
• Only hook up the machine by means of a
fault-current circuit breacker: 30 mA!
A licensed professional electrician must make all electrical
connections and repairs, and observe local regulations in
doing so, especially those regarding protective measures.
The manufacturer or a company designated by the
manufacturer must attend to the repair of all electrical
parts on the machine.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such
action.
Start-up
Observe all safety instructions.
Setting up the machine:
• Set up and run the concrete mixer on a
solid, level base only (where it will not tip
over).
• Keep the machine from sinking into the ground or floor.
Adhere to accident prevention regulations (danger of
tipping).
• When setting up the machine, make sure that the mixing
drum can be emptied without obstruction.
Switching on and off
Be sure that
− all protective devices are on the mixer and properly mounted.
− all safety instructions are adhered to.
• The on/off switch is located beneath the motor housing.
Switch the motor on and off only at the switch.
• In the event of a power failure, the machine will switch off
automatically. Press the switch again to restart the machine.
L Motor protection
The motor is equipped with a thermostat. The thermostat
switches the motor off automatically in the event of overload
(overheating). The machine can be restarted after a cooling-off
period.
… 15 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

atika-dynamic-165

Suche zurücksetzen

  • hinter dem Taster für Ein und Aus ist der Schalter KEDU JD3. Wie gehört dieser angeschlossen? Eingereicht am 4-3-2019 21:38

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Atika Dynamic 165 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info