Bedienungsanleitung Atika HT 315 (Seite 7 von 50) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

519290

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

•

The circular saw bench may only be operated, repaired and main-

tained by persons who are over 18 years old. Ensure that all metal

parts (nails, screws, etc.) are removed from the wood before it is

sawn!

Risks

Certain risks remain as a result of the specific design for the intended

use of the circular saw bench, even if it is properly operated in confor-

mity with its intended use and if all requisite safety rules and regulations

are observed.

Potential risks:

•

Danger for the fingers and hands through improper use of the tool

(saw blade) or workpiece.

•

Injury caused by workpieces hurled out of the circular saw bench.

•

Breakage and ejection of the saw blade.

•

Power hazard if improper electrical connecting lines are used.

•

Contact with live parts when the electrical parts are open.

•

Impaired hearing after working at the circular saw bench for pro-

longed periods without wearing ear defenders.

•

Emission of health hazardous wood dust when the circular saw

bench is operated without a dust extractor.

Further risks that are not immediately obvious can still exist, even if all

precautionary measures have been taken.

The risks can be minimized by strictly adhering to the "Safety Instruc-

tions", "Normal Intended Use" and the operating instructions.

Characteristic noise values

DIN 45635-1651:1990-01

Sound levels Sound levels at the workplace

No-load L

= 101.1 dB(A) L

= 86.1 dB(A)

Load L

= 104.5 dB(A) L

= 89.5 dB(A)

Setting into operation

•

Set up the

circular saw bench

at a location that fulfils the following

conditions:

 Non-slip floor

 Vibration free

 Level

 Free from tripping hazards

 Adequate lighting

•

Check the following

prior to use



Defective connecting

lines (cracks, cuts, etc.).

Never use defective lines!



Proper working condition of the

safety guard

 Correct

splitting wedge setting

(see also Fig. 40).

 Perfect condition of the

saw blade

 The

push stick

must be within easy reach.

•

Never use saw blades that are

cracked

or have become deformed.

•

Do not use saw blades made of

high-speed steel

•

Always stand to the side of the

danger zone

(saw blade) when

working at the bench.

Rotating direction of the saw blade

Ensure that the rotating direction of the saw blade matches the rotating

direction indicated on the guard (33). The rotating direction of three-

phase motors can be changed by inserting a screwdriver in the connec-

tor collar provided for this purpose and turn left or right while exerting a

light pressure to adjust the correct rotating direction.

Mains connection

Compare the voltage specified on the rating plate (on the side of the

table board), e.g. 230 V, with the mains voltage. Connect the circular

saw bench to a correctly earthed socket outlet.

•

Alternating-current motor:

Schuko (earthed) socket, mains voltage 230 V, with earth-leakage

circuit breaker and 16 A fuse.

•

Three-phase motor:

CEE socket, 3-pin + N + PE, mains voltage 380 V or 400 V, with

earth-leakage circuit breaker and 16 A fuse.

Use connecting and extension cables in conformity with IEC 60245 (H

07 RN-F) with a conductor cross-section of at least:

•

-1.5 mm² for a cable length

of up to

25 m.

•

-2.5 mm² for a cable length

exceeding

25 m.

Switching on

⇒

By pressing the top green button of the switch.

The circular saw bench is automatically turned off in the event of a

power failure. Press the green button to switch on again.

Switching off

⇒

Press the bottom red button.

The circular saw bench is fitted with a

braking motor

. The saw blade

must stand still within 10 seconds

after it was switched off

. The brake

is defective if this time is exceeded. The saw must then be repaired by

the manufacturer or a workshop appointed by the manufacturer.

Never operate the saw with

a defective brake

Motor protection

The motor is fitted with a

protective switch

which automatically

switches off the motor when it is overloaded. The motor can only be

switched on again after it has

cooled down

Adjusting the cutting depth

The required cutting depth is adjusted with the crank (5).

Angled cut

⇒

Release the two star grip screws (11).

Adjust the required cutting angle.

Hold the adjusted position.

Tighten the two star grip screws.

Concealed cuts

⇒

Use a normal splitting wedge in conformity with DIN 38 820

(accessory).

Using other saw blades

⇒

Observe the splitting wedge thickness "S"; it is etched into the side

of the splitting wedge.

The splitting wedge must not be thinner than the saw blade, and not

thicker than the kerf width produced by the blade.

The rating plate specifies maximum and minimum saw blade diameters,

as well as the hole diameter.

Using the table extension

A second person working at the saw must stand at the delivery end of

the table extension.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika HT 315 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info