Bedienungsanleitung Atika KS2000 (Seite 25 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Finnisch)

475722

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

 Chopping a tree:

 Clean the working area at the trunk from molesting

perches, brushes and obstacles.

 Clean thouroghly the trunk foot – sand, stones and

other foreign objects make the saw chain edgeless.

 Consider the state of health of the tree – be careful

with trunks with damages or deadwood (droughty,

rotten or dead wood).

 Cut a kerf with the saw of approximately one third of

the tree diameter into the trunk. First of all place the

horizontal cut and then as secondly a cut from top

in an angle of 45°.

 Now saw on the opposite side of the trunk a

horizontal chopping cut. This cut should be placed a

bit higher (appr. 4 cm) than the horizontal cut of the

kerf.

 By no means cut through the trunk. Appr. 1/10 of

the trunk diameter must remain. If the tree starts

falling ahead of time pull out the chain saw

immediately out of the cut and step back or to the

side.

 Push a key into the horizontal chopping cut in order

to make the tree falling.

 Pay attention, when tree starts falling, to perches or

twigs falling down.

Maintenance and cleaning

Before each maintenance and cleaning

work

− switch off device

− wait for stop of chain saw

− pull out main plug

Further maintenance and cleaning works than described in

this chapter shall only be carried out by the manufacturer

or companies named by the manufacturer.

For maintaining and cleaning, removed security devices

must unconditionally be mounted properly and proved

again.

Use only original parts. Other parts can result in

unexpected damages and injuries.

Maintenance

In order to aviod possible injuries wear gloves.

To guarantee a long and reliable usage of the chain saws

carry out the following maintainance works regularly.

Check the chain saw for obvious defects such as

− loose, hung out or damaged saw chain

− loose fastenings

− worn or damaged components

Check the chain saw after each application for

− wear, especially chain, sword and chain wheel.

− correctly assembled and faultless covers and protective

devices.

Necessary repair works or maintainance works have to be

carried out before the usage of the chain saw.

Sharpening of saw chain

For sharpening a saw chain some expertise is necessary.

The saw chain must be regrinded in a specialised shop.

You also get chain sharpening devices in a specialised

shop (filing devices) with which you can sharpen your saw

chain yourself.

You can only work safely and well with a sharp and

clean saw chain.

Exchanging saw chain and sword

Saw chain and sword are exposed to great wearing

demands. Immediately exchange saw chain and sword

when the faultless function is not guaranteed.

 Put the chain saw with motor facing downward on an

even face.

 Remove the cover (10) by loosening the fastening

screw (11).

 Turn the chain clamper (22) anti-clockwise in order to

release the saw chain a bit.

 Take off the sword with saw chain.

 Clean the guide slot thouroughly when only the saw

chain is exchanged.

 When assembling, pay attention that the chain links are

lying correctly within the guide slot and on the chain

wheel (13).

 Turn the chain clamp (22) clockwise until the saw chain

is clamped.

 Now, refasten the cover (10) and clamp the saw chain

as described in paragraph „Clamping of saw chain“.

Chain wheel

The demand of the chain wheel (13) is particularly great.

Check regularly the teeth of the chain wheel for wear or

damages.

A worn or damaged chain wheel reduces the durability of

the saw chain and should therefore immediately be

exchanged by the customer service.

Checking of the oil automatic

Check the function of the automatic chain lubrication by

switching on the chain saw and holding it with the pike in

direction of a carton or paper on the ground.

Do not get in contact with the ground with the chain.

Keep a safe distance of 20 cm.

If an increasing oil track is caused when checking it the oil

automatic works faultless.

If there is no oil track despite full oil tank

 clean the oil flow canal (14) and the upper chain

clamping boring (15)

 If this is not successful please contact the customer

service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika KS2000 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info