Bedienungsanleitung Atika VT32 (Seite 19 von 162) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

475731

Zoom out

Zoom in

Vorherige Seite

1/162

Nächste Seite

 Do not use any defective connection cables.

 When working outdoors, only use extension cables especially

approved and appropriately labelled for outdoor use.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 Only hook up the machine by means of a fault-current circuit

breaker (30 mA).

The electrical connection or repairs to electrical parts of the

machine must be carried out by a certified electrician or one

of our customer service points. Local regulations – especially

regarding protective measures – must be observed.

Damaged mains leads must be replaced by the manufacturer

or one of their service workshops or a similar qualified person

to prevent dangers.

Repairs to other parts of the machine must be carried out by

the manufacturer or one of his customer service points.

Use only original spare parts, accessories and special

accessory parts. Accidents can arise for the user through the

use of other spare parts. The manufacturer is not liable for

any damage or injury resulting from such action.

Handle hoop

 Push the left and the right hoop mount (7 and 8) into the

housing (32). B

 Push the cable strain relief (1) on the handle hoop (2). A

 Connect parts 7 and 8 with 2 by mounting the supplied screws

(4) and wing nuts (6) on both sides. C

 Mount the slide linkage to the bottom of the housing using the 2

screws (31) supplied. Tighten then firmly with a screw driver. D

Switch-plug unit E

 Open the cover of the safety switch (3).

 Push the switch-plug unit on the handle hoop (2) until the holes

on the switch-plug unit align with those on the handle hoop.

 Close the cover and mount the switch using the 2 screws

supplied.

 Mount the cable on the two cable brackets (5) supplied. Make

sure that the cable has enough free motion. F

Grass catching bag – optional accessory, if applicable F

 Pull the impact guard (39) up and hold it.

 Mount the holder of the grass catching bag (40) to the hook on

the housing (32).

Installing the aerator drum - optional accessory G

If the device shall be used as lawn aerator, the scarifier drum (29,

see device description) must be exchanged against the aerator

drum (41).

Before exchanging the drums:

− switch off device

− wait until the drum is stationary

− pull out main plug

Wear protective gloves when exchanging the

drums. Risk of injury!

 Loosen the pan head screws (31) at the seat of the bearing

(30).

 Lift the scarifier drum at the seat of the bearing and pull it out.

 Push the hexagonal protrusion (a) of the aerator drum into the

drive opening (28).

 Remount the seat of the bearing (30) using the screws (31).

To achieve perfect function of the machine, follow the notes

given in these instructions

Mains connection

Compare the voltage given on the machine model plate e.g. 230 V

with the mains voltage and connect the machine to the relevant and

properly earthed plug.

Connect the machine via a circuit breaker switch (residual-current-

operated circuit switch) 30 mA.

 Use connecting or extension cables up to a length of 1.5 m

featuring a core cross section of at least 25 mm².

Mounting of the extension cable H

1. Plug the female connector of the extension cable on the male

connector of the switch-connector combination.

2. Thread the extension cable through the strain relief (1) as a

loop and hang it up.

3. Make sure that the extension cable has enough free motion.

Switching on

Do not use any device where the switch can not be switched

on and off. Damaged switches must be repaired or replaced

immediately by the customer service.

The device is equipped with a safety circuitry preventing

inadvertent switching on.

Start the device only after you have placed it on a low-growth

lawn area.

Switching on .I.

1. Tilt the scarifier slightly towards you so that the front wheel are

above the ground.

2. Push the safety button (a) and keep it depressed.

3. Next, pull the switch lever (b) toward the handle hoop.

4. The scarifier starts and the scarifier drum can rotate freely.

5. Now release the safety button.

Switching off

When you release the switch lever it returns automatically to its

original position.

Motor protection

The motor is equipped with a protective circuit breaker and

switches off automatically in case of overloading. After a cooling-

down break (approx. 15 min), the motor may be restarted.

Release the switch lever because the device will otherwise

restart immediately after it has cooled down. Risk of injury!

Before settings the work depth:

− switch off device

− wait until the drum is stationary

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika VT32 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info