Bedienungsanleitung Atlantic Ingenio (Seite 7 von 45) (Englisch, Französisch, Polnisch)

613599

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

COMFORT Mode : User selects a hot water temperature between 50°C and 65°C (default value of 65°C). Warning: this operating

mode might increase the electrical consumption of the product.

MAX Mode : User selects a hot water temperature between 65°C and 75°C (default value of 70°C). Warning: this operating mode

increases the electrical consumption and scaling. Using hot water with high temperature may cause burns. It is strongly recommended to

take all the necessary precaution to use this operating mode.

5/ Temperature display (Ref. F):

In FROST FREE Mode , it indicates the temperature setpoint of 7°C automatically fixed by the product.

In SMART Mode , the displayed value is the temperature setpoint automatically analysed and fixed by the product. When a large

quantity of hot water is used, the displayed temperature is the one measured close to the bottom side of the product (30cm for a 50L

product, 40cm for 80L and 100L). That means the remaining quantity of hot water is limited (10L of hot water remaining for a 50L product,

30L remaining for a 80L product and 50L remaining for a 100L product).

In MINI , COMFORT and MAX modes, it shows the temperature of water inside the tank. When pushing the setting keys

(Ref. B), the screen displays during a few seconds the setpoint temperature chosen by the user before displaying again the water

temperature inside the product.

6/ Heating indicator (Ref. E): Shows when the water is under heating. NOTA: if the indicator is on continuously, that means the product is under

heating. It doesn’t reveal a bad running of the product.

7/ Control panel locking (Ref. G): To lock or unlock the control panel, press simultaneously the UP and DOWN buttons

TROUBLESHOOTING

When a malfunction occurs, the user interface of the appliance will display an error code.

Code

Fault

Concerned element

Actions

Probe fault

Thermostat

Unplug and plug the power supply

If the problem is not resolved, contact your installer or dealer

No heating

Thermostat

Hot water circuit

Heating element

1/ Check that there are no problems on the hot water circuit (open tap, burst pipe...)

If a leak is found, solve the problem, disconnect and reconnect the power supply to the unit and

check that the default does not reappear during the first heating.

2/ Check that the circuit breaker is not tripped thermal

 Disconnect power supply

 Open the cover of the device

 Check the thermostat

If the circuit breaker has tripped

 reset it by pressing the button SAFETY on the thermostat

 close the cover of the device

 reconnect the power supply and check that the default does not reappear in the first

heating.

If the default reappears, contact your installer or dealer (service code: ERR9).

3/ None of the previous two cases

Contact your installer or dealer (service code: ERR0)

Over heating

Thermostat

Check that the circuit breaker is not tripped thermal

 Disconnect power supply

 open the cover of the device

 check the thermostat

If the circuit breaker has tripped

 reset it by pressing the button SAFETY on the thermostat

 close the cover of the device

 reconnect the power supply and check that the default does not reappear in the first

heating.

If the default reappears, contact your installer or dealer (service code: ERR9).

If the circuit breaker is not tripped, contact your installer or dealer (service code: ERR9)

Dry heating

Cold water circuit

1/ Check that the cold water supply is operational

2/ Open hot water taps and see the water flow. If the flow is not immediate, wait lines are

purged of air

If the flow of the hot water circuit is sufficient

Disconnect and reconnect the power supply to the unit and check that the default does not

reappear.

If the default reappears, contact your installer or dealer (service code: Err7).

If the flow of hot water is absent, contact a qualified professional to intervene in the cold

water supply of the unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atlantic Ingenio Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info