Bedienungsanleitung Atlantic Shangai Ecodomo (Seite 8 von 22) (Englisch, Französisch, Portugiesisch, Spanisch)

613624

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

2) Fixing the comfort temperature :

The comfort temperature is the temperature that you would like while the room is occupied.

a) Put the switch to

b) Set the control knob on 5, the heating indicator V1 comes on if the room temperature is below the required

temperature.

c) Wait a few hours for the temperature to stabilise.

d) If the setting is satisfactory (if necessary use a thermometer to check), mark the position for future use.

If the setting is not satisfactory, adjust it and start again from point c.

3) Fixing the Eco temperature :

This is the required temperature during periods when the room is unoccupied. It is recommended theat this mode should

be used if the room is unoccupied for more the 2 hours.

a) Set the cursor switch knob to

a) Adjust the control knob between 3 and 4, the heating light V1 comes on, if the ambient temperature is lower than the

instruction of desired Eco temperature.

b) Wait a few hours until the temperature stabilizes.

c) If the setting is satisfactory (if necessary use a thermometer to check), mark the podistion. If the setting is not

satisfactory, adjust it and start again from point c.

Note : When switching n°1 (on the picture) is set on Programming system (clock symbol) with the PassProgram On/

Off, please refer to paragraph n°8.

4) Frost-Free mode :

This mod e is used to keep the temperature at approximately 7°c in the room when you are absent from the house for

a prolonged period (i.e. mor than 24 hours).

a) Set the  switch on

5) The heating indicator : V1

This light comes on when the heating element is working. It may flash when the temperature has stabilised.

6) Switching off the device :

Move the cursor to .

7) Locking the controls :

It is possible to lock or limit use of the control knob and lock the switch to

prevent unauthorised manipulation of the panel heater (children, etc.).

a) Unhook the panel heater from its wall mounting.

b) Remove the slugs P on the back of the thermostat fro their mountings.

c) Select position B to lock the control knob or position L to limit the amount it

can be turned. Position M blocks the switch.

8) Using the pilote wire :

The product with pilote wire can receive the following signals from a master unit :

- Comfort (temperature of  control knob)

- eco (comfort temperature -3°C to -4°C)

- Frost free (approximately 7°C)

- Off

Put the switch  to the programming mode (clock symbol).

The product must be connected through the pilote wire to a programming control or a product equipped with pass

program system in order to use these different modes. You can control several convectors with a single programmer

or a product equipped with pass program system;

Warning : The control unit will consider frost free and off signals in any switch selection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atlantic Shangai Ecodomo Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info