Bedienungsanleitung Atmos A25 (Seite 46 von 96) (Englisch)

810409

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

www.atmos.cz

46-EN

Operation and maintenance manual - EN

• After the ignition of pellets the photocell will sense light, which will cause the ignition spiral to

switch off with a slight delay.

• The burner will pass over to the stage of perfect burning of fuel - set by parameter T7.

The OPERATION algorithm consists of the following steps:

• When the fuel burns perfectly, the burner will get to the stage of gradual increase of the power

to the nominal value - parameter T10.

• After achieving the nominal power the burner works in the normal mode until the heating system

or the accumulation tank is heated to the required temperature. The power of the burner results

from the hourly quantity of pellets delivered by the worm conveyor to the combustion chamber.

The worm conveyor works in the intermittent mode set by parameters T4 and T6. Parameters

T4 and T6 are set in accordance with the instructions on page 50.

•

After setting the nominal power of the burner you must also set the amount of combustion air

necessary for complete burning of fuel. This setting is performed with the air flap on the burner

fan. The exact setting should be carried out by a trained person with the use of a flue gas

analyzer.

The burning out algorithm is designed as follows:

•

After the achievement of the set temperature at the boiler thermostat (e.g. 85 °C) or temperature

in the accumulation tank - temperature at the bottom sensor (TS), the electronic control unit of the

burner will switch off the external worm conveyor. Thanks to this, the pellets in the combustion

chamber will burn out. Optimal burning out of pellets in the combustion chamber is additionally

supported by the operation of the burner fan for a certain time - parameter T5. After subsequent

drop of the temperature of water in the boiler or discharge of the accumulation tank - temperature

at the top sensor (TV), the burner will be re-started in the same way as described in the text above.

If the accumulation tank is connected to a solar exchanger and activating functions for automatic

optimization (switching) of sensors, parameter S15 = 3, the burner may be turned off by sensor TK

instead of sensor TS.

The other algorithms are designed in the following way:

• If the first attempt for ignition with fuel supply fails, the burner will repeat the whole algorithm.

After the second unsuccessful attempt for ignition with fuel supply the burner will proceed to the

third attempt during which the fuel is not supplied any longer, but only the ignition spiral is active.

After this unsuccessful attempt the burner will be put out of operation as the system has probably

run out of pellets or a fault has occurred.

• In case of a short-term interruption of power supply to the burner, the burner will automatically

renew its operation after performing diagnostic checks, complete burning out of pellets and a

new start.

INFO - This sequence has been set intentionally to ensure safe and trouble-free operation

of the burner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A25 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atmos A25

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info