Bedienungsanleitung Atmos A25SP (Seite 10 von 72) (Englisch)

810413

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.atmos.cz

10-EN

Operation and Maintenance Manual - EN

4. Safety, burner installation and commissioning

Safety and connection of the burner to the boiler

WA R N I N G - Before starting the burner you must carefully read all the provisions of this

manual. At the same time you must observe all general safety regulations for work with

heating equipment resulting from the valid legislation.

• The premises where the equipment will be installed must comply with all fire protection regulations

in accordance with valid standards and laws.

• The equipment must be positioned in such a way to ensure access for cleaning and removal of

ashes not only from the burner, but also from the boiler, flue gas duct and chimney.

• The burner must be installed to the boiler over a sealing cord, soft Sibral sealing or another

insulation and sealing material to prevent flue gas from escaping along the burner to the boiler

room. Under one of the nuts with the use of which the burner is attached to the boiler a SPECIAL

SHEET-METAL PART - END SWITCH STOP must be positioned. It is used to compress the

end switch that monitors the proper position of the burner on the boiler. This protective device

must not be omitted in any case as it is directly related to fire safety.

• The connection between the burner and the boiler must be properly tightened to prevent flue gas

from escaping to the boiler room.

•

During the installation you must make sure that the pellets can freely fall through the hose to the

burner. The connections between the hose, burner and conveyor must also be properly tightened.

Design and technical measures for increasing safety

• The ignition and combustion process is controlled by the electronic control unit by means of the

flame sensor - photocell. If the sensor does not sufficiently see the flame during operation, it will

automatically put the burner out of operation.

• The electronic control unit senses the speed of the burner fan and at any problems of the fan it

automatically puts the burner out of operation.

• On the burner frame there is an end switch and end switch stop that does not make it possible to

start to burner if the burner is not properly fixed to the boiler (e.g. after cleaning of the burner).

If during normal operation of the burner the end switch gets disconnected, the burner will be

automatically put out of operation. If at the start after two attempts with the fuel supply and one

attempt without the fuel supply the pellets are not ignited, the burner will be automatically put out

of operation.

• If during normal operation of the burner the fuel bin runs out of pellets, the burner will try a new

start and subsequently will be put out of operation. After replenishing pellets in the fuel bin and

drawing pellets to the conveyor you can start the burner by merely turning off and on the burner

switch on the boiler panel.

• The flexible transparent hose between the burner and external conveyor is made of special material

that melts at high temperatures and the hose will change to a spring that will separate the burner

from the fuel bin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A25SP Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info