Bedienungsanleitung Atmos A45 (Seite 14 von 76) (Englisch)

810410

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

14-EN

Operation and maintenance manual - EN

www.atmos.eu

Kotle

Komín

7. Flue gas duct of the boiler

The flue gas duct from the boiler must lead to the

chimney vent. If the boiler cannot be connected directly to

the chimney vent, the corresponding flue gas duct adapter

must be as short as possible with regard to the particular

conditions, but not longer than 1 m, without additional

heating surface and it must rise towards the chimney. Flue

gas ducts must be mechanically strong and leak-proof for

flue gas and cleanable inside. Flue gas ducts must not lead

through other owners‘ residential or commercial units. The

inner cross-section of the flue gas duct must not be larger

than the inner cross-section of the smoke uptake and must

not get narrower towards the chimney. The use of smoke

elbows is not suitable. Designs of passages of flue gas du-

cts through structures of flammable materials are defined in

Annexes 2 and 3 of ČSN 061008 and are mainly suitable for

mobile units, wooden huts, etc.

1 - Flue gas thermometer

2 - Cleaning opening

3 - Draught regulator (limiter) / throttling flap

INFO - In case of too strong draught of the chimney install a throttling flap /3/ or a draught

reducer in the flue gas duct, see the ATMOS price list.

8. Fire protection within the installation and use of heat appliances

Extract from ČSN 061008 - Fire safety of local appliances and sources of heat

Safe distances

On installation of an appliance the safe distance from building materials must be maintained, at

least 200 mm. This distance is valid for boilers and flue gas ducts located near flammable materials of

the B, C1 and C2 flammability class (the flammability class is specified in tab. no. 1). The safety dis-

tance (200 mm) must be doubled if boilers and flue gas ducts are located near flammable materials of

the C3 class (see tab. no.1). The safety distance must be doubled if the flammability class of flammable

material is not evidenced. The safety distance may be reduced to a half (100 mm) if you use a non-

-flammable heat insulating panel (asbestos panel) with the thickness of at least 5 mm, located 25 mm

from the protected flammable material (flammable insulation). A shielding panel or protective screen

(on the protected object) must exceed the outline of the boilers (incl. flue gas ducts) at each side by at

least 150 mm and the top surface of the boiler by at least 300 mm. A shielding panel or protective screen

must also be used to protect fixtures of flammable materials if the safe distance cannot be maintained

(e.g. in mobile units, huts, etc. - more details in ČSN 061008). The safety distance must also be main-

tained in case of installation of fixtures near boilers.

Chimney

Boiler

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atmos A45

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info