Bedienungsanleitung Atmos A45SPT (Seite 40 von 72) (Englisch)

810414

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.atmos.cz

40-EN

Operation and Maintenance Manual - EN

m) S14 = 13…..Reserve function is the reverse output function for controlling the pump in the

boiler circuit from the burner regulation (output cable from boiler with a connector – white inside)

via AD02, AD03 or AD08 modules (factory setting). This function controls the pump in the boiler

circuit using AD02, AD03 or AD08 modules ranged into a set with pump thermostat installed into

the boiler panel. After activation, S37, S38, S39, S40 temperature parameters must be checked and

configured.

For this function the AD08 module is situated under boiler control panel in DC40GSP boilers,

see wiring diagram.

For this function the AD03 module is situated under boiler control panel in DC40SPT boilers,

see wiring diagram.

n) S14 = 14….. Reserve function for direct control of solar heating pump from the burner regulation

(boiler terminal board). This function control solar pump when automatic sensor switching function

is activated (S15 = 3), where the boiler is connected with accumulation tank equipped with solar

exchanger and collectors. The system requires TV, TK, TS and solar sensors to be connected to the

TSV solar panel. This function never uses AD02 or AD03 modules.

After activation, S26, S27, S28, S29, S30, S31, S32, S33 temperature parameters must be checked

and configured.

This function is specially designed for boilers: D30P, D31P, D40P a D50P

CAUTION - the direct controlling function of solar heating from pellet burner cannot be used

for DCxxGSP(SP) boilers and boilers with burner built into the upper doors. This function

also cannot be used when the pump is simultaneously controlled in the boiler circuit from the

burner regulation (TK sensor cannot be simultaneously in boiler and accumulation tank)

o) S14 = 15….. Reserve function for the compressor control during the function for automatic

burner cleaning using compressed air. Power element designed for switching and powering the

compressor (e.g. contactor) must be connected between reserve output R2 and the compressor.

This function is connected with S6(14), S41, S42, S43, S44, S45, S46, S47 parameter, which must

be checked and configured.

p) S14 = 16….. Reserve function for controlling el.fan during the function for automatic burner

cleaning using compressed air. This function is connected with S6 (14), S41, S42, S43, S44, S45,

S46, S47 parameter, which must be checked and configured.

Special function for turning on reserve output R2 according to the temperature of a concrete

sensor:

a) e.g. function: TS>……. means that if the TS sensor temperature is higher then the set value in

S52 parameter – Temperature C, reserve output R2 will be activated

b) e.g. function: TS<……. means that if the TS sensor temperature is higher then the set value in

S52 parameter – Temperature C, reserve output R2 will be deactivated

c) e.g. function: TS,TV>……. means that if the TS and TV sensor temperature is higher at the same

time then the set value in S52 parameter – Temperature C and S54 – Temperature D, reserve output

R2 will be activated (Temperature C = first position (TS), Temperature D = second position (Tv)).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45SPT Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info