Bedienungsanleitung Atmos A45SPT (Seite 41 von 72) (Englisch)

810414

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Operation and Maintenance Manual - EN

www.atmos.cz EN-41

d) e.g. function TS,TK<……. means that if the TS and TK sensor temperature is higher at the

same time then the set value in S52 parameter – Temperature C and S54 – Temperature D, reserve

output R2 will be deactivated (Temperature C = first position (TS), Temperature D = second

position (Tk)).

Individual functions:

• Parameter S15 –

Operation function of the burner by the two temperatures in the accumulation tank …(1)

a) S15 = 1… The function is off, the burner works based on the thermoregulator on the boiler panel

b) S15 = 2 …. The function is activated and the pellet burner works based on the two temperatures

(sensors) in the accumulation tank – TV and TS (recommended tank volume: 500 to 1000 l).

The temperature of the bottom sensor (TS) is the temperature at which the burner is switched off

and the fuel burns out.

The temperature of the top sensor (TV) is the temperature at which the burner is switched on again.

c) S15 = 3 …. The function is activated and the pellet burner works based on the two temperatures

(sensors) in the accumulation tank – TV and TS (recommended tank volume: 500 to 1000 l).

The temperature of the top sensor (TV) is the temperature at which the burner is switched on again.

The temperature of the bottom sensor (TS or TK) is the temperature at which the burner is stopped.

Whether the burner is switched off based on the TS or TK sensor is decided by the temperature of

the solar panel (TSV) and the temperature in the lower part of the accumulation tank (TS), where a

solar exchange is built-in. If the solar panel can efficiently heat up water in the accumulation tank,

the burner is turned off based on the TK sensor, so that the tank can store energy from the sun.

If the energy delivered from the solar collector drops below a certain limit (temperature), the

deactivation logic of the burner is automatically switched back to be based on the TS sensor (S26 = 1).

However, it is possible to set that the switching may only occur after a certain period of time (S29

= 2nd digit means the length of delay between switches, in hours). Another variant is to have the

burner work permanently based on the TV and TK temperatures (S26 = 0).

d) S15 = 4 …. The function is off and the burner works based on the TK temperature, protected

by the thermoregulators on the boiler panel. After this function is activated, we need to check and

possibly setup its temperature parameters S18 and S19.

CAUTION - if S15 = 2 not possible to set S6 = 14 and S14 = 14.

If S15 = 3 not possible to set S6 = 11, S14 = 11, S6 = 12, S14 = 12, S6 = 13, S14 = 13.

If S15 = 1, S15 = 4 not possible to set S14 = 14.

(17) TS>

(18) TS<

(19) TV>

(20) TV<

(21) TK>

(22) TK<

(23) TSV>

(24) TSV<

(25) TS,TV>

(26) TS,TV<

(27) TS,TK>

(28) TS,TK<

(29) TS,TSV>

(30) TS,TSV<

(31) TV,TK>

(32) TV,TK<

(33) TV,TSV>

(34) TV,TSV<

(35) TK,TSV>

(36) TK,TSV<

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45SPT Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info